EN 61008

EN 61008

Understanding the purpose and limits of residual-current protection

The EN 61008 series covers residual current operated circuit-breakers without integral overcurrent protection, known as RCCBs, for household and similar uses. General rules are addressed in EN 61008-1. An RCCB detects residual current and disconnects the protected circuit; suitable overcurrent protection must be provided separately for overloads and short circuits.

Residual-current protection monitors the sum of currents passing through the circuit's live conductors. In a single-phase circuit, an imbalance occurs if some outgoing line current returns by a path other than the neutral. The distinction between MCBs, RCCBs and RCBOs therefore matters: an MCB covered by EN 60898 provides overcurrent protection, while an RCBO covered by EN 61009 combines residual-current and overcurrent protection.

Editor's note: A 40 A marking on an RCCB does not mean it automatically trips when current exceeds 40 A. The 30 mA marking is its rated residual operating current, not its load current. Keep current-carrying capability separate from residual-current sensitivity.

Assess amperes, milliamperes and pole count together

The rated current In relates to the current the device can carry under specified conditions. The rated residual operating current IΔn describes the sensitivity of its residual-current function. For example, Hager's CD440J data lists four poles, 40 A, 30 mA and Type A together. These ratings describe different characteristics and are not interchangeable.

Additional protection at 30 mA or below provides an extra protective measure against electric shock in appropriate applications; it does not replace basic insulation. Ratings such as 100 mA or 300 mA do not provide the same additional protection as 30 mA. Select sensitivity, delay and circuit coverage according to the applicable installation rules.

The RCCB itself requires overload protection

Where an RCCB supplies several outgoing circuits, fitting an MCB on each circuit does not automatically limit the total current through the RCCB. Assess the expected load, RCCB rated current, temperature conditions inside the assembly and associated overcurrent protection together. Protective device selection requires more than checking each device's label separately.

BEAMA specifically distinguishes short-circuit coordination from overload protection. For example, an assembly passing a short-circuit test with an upstream 100 A fuse does not, by itself, establish that this fuse also protects a lower-rated RCCB against overload. Load assessment and overload protection are separate checks. The arrangement must match the device and assembly manufacturers' verified requirements.

Conditional short-circuit current is not independent breaking capacity

Inc is the rated conditional short-circuit current stated for the RCCB. It applies in association with a specified overcurrent protective device. Im and IΔm making and breaking capacities describe different characteristics; not every kA value has the same meaning. Do not interpret an RCCB's conditional rating as a circuit breaker's independent short-circuit breaking capacity.

Hager publishes an Inc rating of 6 kA for the CD440J. That number alone is not an instruction for selecting the associated protection. Compare prospective short-circuit current, operating voltage, and the exact fuse or circuit-breaker type and rating with the manufacturer's coordination data. A table for a different product family cannot simply be applied to a similar-looking device.

RCD type and selectivity are separate from sensitivity

Type AC, A, F and B RCDs respond to different residual-current waveforms. For electronic power supplies, inverters and variable-speed loads, knowing the rated current alone is insufficient. Assess the residual currents the load can produce and the manufacturer's required RCD type. Supplementary requirements such as EN 62423 also apply to Type F and Type B devices.

Connecting a 30 mA RCCB in series with a 300 mA RCCB does not, by itself, guarantee selectivity. Time delay and manufacturer coordination also matter. Identifying which protective device operated helps locate the affected circuit; a selective time-delayed device must not casually replace the fast additional protection required for a circuit.

Arrange neutrals, earthing and supply direction correctly

The protected circuit's line conductors and neutral, where present, must pass through the same RCCB's sensing arrangement as specified by the manufacturer. Mixing its outgoing neutral with another protection group, or introducing an incorrect downstream neutral-to-earth connection, can cause RCCB tripping. Neutral and protective conductors are not interchangeable.

Protective earthing and equipotential bonding perform separate safety functions. An RCCB being able to trip for certain leakage faults does not make an installation without earthing compliant. Follow LINE/LOAD markings and supply direction; installations involving PV, batteries or reverse power flow also require verification of unidirectional or bidirectional suitability.

A test button does not measure the entire installation

The test button uses an internal test circuit for a functional check; it does not establish that earthing at a socket has been verified. Perform functional checks at the intervals specified by the manufacturer. If the device fails to trip, do not rely on its protective function; arrange inspection by a qualified person.

Product testing and installation verification serve different purposes. Operating-time measurements require a suitable instrument, correct settings and the applicable installation rules. For intermittent or rain-related tripping, investigate moisture, insulation deterioration, connected equipment and accumulated leakage. Switchboard maintenance also checks connections and signs of overheating; device replacement requires appropriate isolation and verification.

Editions, conformity documents and protection limits

At the check on 15 October 2026, BSI listed BS EN 61008-1:2012+A12:2017 as current and under review. Internationally, IEC 61008-1:2024 has been published. Its stated scope covers RCCBs not exceeding 440 V AC and 125 A at 50 Hz, 60 Hz or 50/60 Hz. The IEC edition, EN edition and local adoption are separate records.

CE marking is not an automatic safety certificate issued by a central body. Match the exact model, standard edition, technical documentation and EU Declaration of Conformity. An RCCB also does not automatically provide SPD or voltage monitoring relay functions. Residual-current protection cannot be relied upon for simultaneous contact with line and neutral where no residual-current imbalance occurs.

Related guides

Circuit protection, residual current protection and electrical safety
Overview of CENELEC standards
Fuse and protection standards
Fuse products