Machinery Safety Standards: Finding the Right Guide

Machinery Safety Standards
Machinery safety standards organize methods for design, protective measures and validation to protect people from machine hazards. Automation can make a process faster; safety work considers possible harm during production, setting, cleaning and maintenance. Choosing the right document among industrial standards starts with understanding the machine’s hazards and limits of use.
How do type A, B and C standards fit together?
Type A standards provide basic principles; ISO 12100 is the starting point. Type B standards address safety aspects or safeguards applicable across different machines. Type C standards address a particular machine group. Check the applicable type C standard and its scope; differing provisions take priority for the matters it covers. When reading IEC standards and EN standards, check the edition, amendments and national adoption together.
Where does risk reduction start?
Inherently safe design comes first: for example, changing the mechanical arrangement to reduce a crushing hazard. Guards and other technical protective measures follow. Information for use, warnings and necessary training then address remaining risks. A warning label cannot replace an applicable technical safeguard. Risk assessment considers reasonably foreseeable misuse and interventions as well as normal production.
The roles of the main standards
| Standard | What does it address? |
|---|---|
| ISO 12100:2010 | Hazard identification, risk assessment and risk reduction. |
| ISO 13849-1:2023 | Design of safety-related control parts using the PL approach. |
| ISO 13849-2:2012 | Validation of safety functions through analysis and testing. |
| IEC 62061:2021 + AMD1:2024 + AMD2:2026 | Functional safety of machinery control systems using the SIL approach. |
| IEC 60204-1:2016 + AMD1:2021 | Electrical equipment of machines. |
| ISO 14120:2015 / ISO 14119:2024 | Guard construction / interlocking devices associated with guards. |
| ISO 13857:2019 / ISO 13855:2024 | Distances preventing access by limbs / positioning of safeguards. |
| ISO 13850:2015 / ISO 14118:2017 | Emergency stop / prevention of unexpected start-up. |
Edition check: 10 October 2026. The table identifies published ISO/IEC editions. Drafts do not count as published replacements. The edition applicable to a project and any machine-specific standard must be established separately.
PL and SIL: a score for the whole machine?
Under ISO 13849, the required performance level (PLr) is determined for a particular safety function; the achieved PL is evaluated separately. Architecture category alone is insufficient: component reliability, diagnostics and common cause failures also matter. Under the SIL approach, the target and achieved result likewise relate to a safety function. The articles on SIL 1, SIL 2 and SIL 3 explain the concepts; a product label does not determine the required level.
Practical example: a packaging machine with a guard door
An operator opens a guard door to remove a jammed product. First assess hazardous movement, stopping time and the access route. ISO 14120 addresses guard construction; ISO 14119 addresses interlocking device selection. If movement does not stop immediately, assess whether access must remain prevented until a safe standstill. Seeing the door signal in a standard PLC program alone does not validate the safety function.
A sensor, inductive sensor, photoelectric sensor or limit switch can be useful for production control. Ordinary detection devices do not automatically qualify as safety devices. On the output side, the suitability and failure behaviour of the contactor, relay and motor drive must also be assessed for the function. Understanding switchgear helps when reading this assessment.
Emergency stop, maintenance and validation
Emergency stop does not replace safeguards. Releasing or resetting the emergency stop device must not automatically restart the machine. Maintenance requires more than a “stop” command: assess unexpected start-up and stored energy. Electrical supplies, compressed air, springs and gravity can all create hazardous movement.
The validation file connects the safety function specification, target PLr or SIL, selected components, calculations, software/parameter versions and analysis-test results. In the packaging example, guard opening, reset and restart behaviour are tested against the specified requirements. Acceptance requires more than observing that the machine “works”.
Official sources: ISO 12100 · ISO 13849-1 · ISO 13849-2 · IEC 62061 · IEC 60204-1 · ISO 14119 · ISO 13855 · ISO 13850 · ISO 14118 · ISO/TC 199 · DGUV / IFA