6ES5 456-6AA12
Siemens 6ES5 456-6AA12 — 8-Channel 220 V AC Digital Output Module
6ES5 456-6AA12 is an eight-channel, galvanically isolated AC digital output module for older SIMATIC S5 systems. Siemens ST 53 lists it in the Robustbauform construction with a 220 V AC nominal rating and 2 A per channel.
The exact-code ordering table marks S5-130A and S5-150A as its systems. Check the rack and mechanical version against the installed S5 arrangement. The 456-6 specification gives a 176–264 V AC load-voltage range and a 50 mA–2 A output-current range.
Total load and cabinet temperature
At 55 °C, total loading is limited to 30% of the sum of all nominal output currents. This gives a calculated 8 × 2 A × 0.30 = 4.8 A total. Do not assume that all eight channels may carry 2 A simultaneously; include this limit in the supply and cabinet load assessment.
For contactor coils, assess pickup current and release behaviour together. Read the coil specifications for Siemens contactors in their own documentation. Switching limits are 2 Hz at nominal inductive load and 20 Hz for resistive loads.
Off-state behaviour, protection and indications
Specified off-state leakage is 5 mA maximum. When selecting small interposing relay coils or light loads, account for this and the 50 mA minimum load current. Do not assess the off-state behaviour of an electronic output as though it were a mechanical relay contact.
Short-circuit protection uses a fuse with a trip indication. The catalogue drawing identifies a red LED for fuse failure and a green LED for signal state. Check the PLC output command separately from actual load energization; a signal indication alone does not prove that the load circuit is healthy.
Follow the Robust 456-6 diagram for front wiring and cable connections. When replacing a fuse, verify its type and rating against the card’s instructions and correct the load fault. If an external SSR or interposing device is added, assess its control input and load conditions separately.
Differences from other 456 and 458 models
456-4UA11 and 456-4UA12 are U-series parts with different mechanical and system arrangements. 456-7LA11 and 456-7LB11 are separate S5-115U models. Do not select them as replacements for 456-6AA12 solely because their numbers begin with 456.
458-7LC11 is a relay-contact output, while 450-6AA12 is a different Robust DC output module. Similar family names do not establish matching load voltage, channel arrangement or wiring.
Used-module selection and functional checks
During fault investigation, check channel command, AC load supply, fuse, front wiring and actual load current in order. Voltage seen on an off channel with a high-impedance meter is not sufficient on its own to diagnose a shorted output. Perform measurements and removal under appropriate safe conditions.
For a used module, assess the complete label, hardware revision, front connections and all channels tested with suitable loads. Preserve the PLC program, memory backup and wiring photographs of the existing S5 system before intervention.
Editor’s note
Check the 6AA12 suffix together with the Robust construction. Old S5 names can look very similar. Establish the rack and connection arrangement before buying a card that may be healthy but unsuitable for the installation.
Do not simply multiply the 2 A marking by eight and stop there. Cabinet temperature and simultaneous loads change the calculation. Write down what each channel operates before deciding how much the module can carry.
If a small relay will not release when commanded off, check the load conditions before condemning the card. Electronic-output leakage and the coil’s release threshold may both be involved.
If a fuse has opened, inspect the cable and connected load before fitting another. Verify the correct replacement rather than increasing the fuse rating to keep the circuit running.
For a used module, check all eight channels and look for darkened connectors or heating around the fuses. Take clear photographs before removing the original card; they are useful when maintenance gets busy.
OtomasyonAVM resources and PDFs
+ OtomasyonAVM S5 PDF archive · About Siemens S5 PLCs. The main source for this model is Siemens ST 53, 1985: specifications on 8/7, wiring on 8/21 and the complete order code on 9/6. The document is in German.
Related topics
+ 456-4UA11 · 456-4UA12 · 456-7LA11 · 456-7LB11 · 458-7LC11. Verify the system and output type separately.
Browse SIMATIC S5
+ S5 digital output modules · SIMATIC S5 · Siemens S5 PLC · Siemens second-hand equipment.