6ES5 374-2KK21

Siemens 6ES5 374-2KK21 – SIMATIC S5 1 MB Long-Format Flash EPROM Memory Card

The Siemens 6ES5 374-2KK21 is a 1 MB long-format Flash EPROM card in the SIMATIC S5 MC 374 range. This 5 V only generation uses 5 V for both reading and writing. The Siemens ST 50 catalog lists this order number for the S5-155U CPU 948 and the S5-155H CPU 948R/948RL.

The card retains the STEP 5 application and stored data blocks when power is off. During an overall reset, the CPU 948 copies the blocks from the card into internal RAM. Blocks subsequently downloaded to the CPU through the PG connection can therefore differ from the Flash copy.

CPU 948 and redundant S5-155H compatibility

Page 4/29 of Siemens ST 50 lists the card alongside the 6ES5 948-3UA11 and 6ES5 948-3UA21. These CPUs provide 640 KB and 1,664 KB of internal user memory respectively. The 1 MB marking is the card’s storage capacity. Use the CPU’s own memory limit when checking the size of the application to be loaded into RAM.

The S5-155H table lists the 948R 3UR12, 948R 3UR22 and 948RL 3UR51. In a redundant S5 rack, record whether the card came from the master or standby CPU. Follow the applicable COM 155H procedure for card replacement and program synchronization.

For another CPU with a long card slot, check its ordering table. For example, Siemens lists the 374-2KG21 for the CPU 928-3UA21 and CPU 928B-3UB21. That card is rated at 128 KB, with 64 KB usable on those CPUs.

Data block storage on the CP 516

The CP 516, 6ES5 516-3UA11, is an S5 expansion module that supports 5 V only Flash cards from hardware revision 2. Siemens lists the 2KK21 in the CP 516 accessory table. Its two card slots are addressed as A: and B:. If the card holds recipe or setup data, record the slot and the section containing the data blocks when taking a backup.

Programming and differences from earlier Flash cards

For a CPU 948 application, prepare the card offline on a compatible SIMATIC programmer. Siemens ST 50 lists the 6ES5 985-2MC11 programming adapter. The Siemens notice for this 5 V only generation specifies STEP 5 V6.6 for programming. The Flash memory is electrically erasable. After writing the card, read it back and compare the blocks with the source file.

Siemens identifies the 374-2KK21 as the 5 V only replacement for the earlier 374-2FK21. The earlier generation uses 12 V to write and 5 V to read. In the long-format 5 V range, the 374-2KH21 holds 256 KB and the 374-2KL21 holds 2 MB.

The similar-looking 374-2FH21 is an earlier Flash card. The 374-1KH21 is a short-format 5 V Flash card, and the 374-2AH21 is a long-format RAM card. Check the full order number, card format, memory type and voltage generation before selecting a spare.

Editor’s note

Photograph both labels. Make sure the 2KK21 suffix and the host device’s order number are readable. For a CP 516, record the hardware revision too.

Keep two backups before an overall reset. Save the current program from the CPU and the copy read from the Flash card as separate files. Compare any blocks changed since the card was last written.

Check the programming setup if the PG cannot identify the card. Verify 5 V only support, the STEP 5 version and the adapter type. This lets you troubleshoot the card and the programming setup separately.

Label both sides of an S5-155H. Record which CPU each card came from, which side was master or standby and which project version was read from each card.

Ask how a used card was tested. Confirm that a compatible programmer recognized it and that the test included writing and reading it back. Compare the card intended for the machine with the approved STEP 5 project.

OtomasyonAVM resources and PDFs

About Siemens SIMATIC S5 systems · OtomasyonAVM S5 PDF archive

Related topics

374-2KH21 256 KB Flash · 374-2KL21 2 MB Flash · CP 516 memory module

Site navigation

Siemens SIMATIC S5 › S5 CPUs and modules › S5 memory cards

External references

Siemens 4202137 – 5 V only Flash cards and replacement order numbers (PDF, German)

Siemens ST 50 – CPU 948 and S5-155H ordering tables, pp. 4/29 and 4/32 (PDF)

Siemens S5-135U/155U system manual – 374 Flash cards, Section 5.8 (PDF)

Siemens S5-155H manual – memory card replacement, Section 9.6 (PDF)