what is DC bus?

What is a DC Bus (DC Link)?

Inside a variable frequency drive, the DC bus is the intermediate DC circuit between the input rectifier and the output inverter. Incoming AC power is first converted to DC, smoothed by the DC-link capacitors, and then used by the inverter stage to create the controlled output that runs the motor.

So the DC bus is more than a pair of positive and negative conductors. The rectifier, DC-link capacitors, optional DC choke, braking circuit and inverter power stage all belong to the same energy path. For the complete AC–DC–AC picture, see our VFD technical guide.

DC bus and DC link inside a variable frequency drive

How is the DC bus created inside a VFD?

In a conventional AC drive, the incoming supply first passes through a rectifier bridge. The rectifier converts AC into pulsating DC. A bank of DC-link capacitors then smooths this voltage and provides an energy reservoir for the inverter stage.

The inverter uses IGBTs or similar power semiconductors to switch the DC bus at high speed and generate PWM. The motor therefore does not simply receive a perfect sine wave directly from the drive. Instead, the switching pattern is controlled so that the required fundamental voltage, current and frequency are produced at the motor.

3-Phase AC → Rectifier → DC Bus → PWM Inverter → Motor

3-Phase AC Input

Three waveforms, 120° apart

DC Bus (+ / −)

Smoothed DC-link voltage

PWM Inverter Output

Pulse width follows a sinusoidal reference

What voltage should you expect on the DC bus?

There is no single DC-bus voltage that applies to every drive. The actual level depends on the mains voltage, rectifier topology, DC choke, loading and front-end design. In a conventional capacitor-input drive, the DC link approaches the peak value of the incoming line-to-line voltage.

As a useful field reference, a 230 V AC drive may operate around 310–325 VDC, a 380 V AC drive around 515–540 VDC, a 400 V AC drive around 540–565 VDC, and a 480 V AC drive around 650–680 VDC. These figures are not trip thresholds. Always use the manufacturer's specified limits for the actual drive.

One important detail: a standard diode-front-end VFD does not regulate its DC bus like a laboratory DC supply. The bus naturally moves with mains voltage, load and regenerative energy. Active-front-end and regenerative drives can control the DC-link voltage much more actively.

Editor's note: If a drive keeps tripping on DC Bus Overvoltage during deceleration, do not immediately blame the incoming mains. A high-inertia machine can push energy back into the drive faster than the DC link can absorb it. In other words, the high voltage may be coming from the moving machine itself.

Why does the DC bus rise during braking?

During normal motoring, energy flows from the DC bus toward the motor. During rapid deceleration, however, the motor can become a generator. Mechanical energy from the motor and load is converted back into electrical energy and flows into the DC link.

If that energy has nowhere to go, DC-bus voltage rises. The drive may first reduce regenerative torque or extend the deceleration time. Where stronger braking is required, a braking unit / brake chopper switches a suitable braking resistor across the DC link and converts the excess energy into heat.

Our dynamic braking guide shows this energy flow in more detail. This should not be confused with DC-injection braking, where the drive creates braking torque by applying DC current to the motor windings.

What is a common DC bus?

A common DC bus allows two or more drive sections to share the same DC link. The useful part is energy exchange: while one axis is regenerating during deceleration, another axis that is accelerating may use part of that energy directly.

This approach is common in multi-axis machinery, winding and unwinding systems, test rigs and servo systems. Instead of turning every bit of regenerative energy into heat, the machine can reuse some of it internally.

A common DC bus is not simply a matter of joining all positive terminals together and all negative terminals together. Pre-charge arrangements, DC fusing, isolation, conductor sizing, grounding strategy and the drive manufacturer's common-bus requirements must all be considered. Drives that are not designed or approved for common-bus operation should not be connected this way.

A PLC or HMI is not part of the DC power path itself. However, when the drive exposes the relevant parameters over its communications interface, the control system can monitor DC-bus voltage, overvoltage and undervoltage status, drive loading and fault information. That makes the DC link useful not only for power conversion but also for machine diagnostics.

What causes high or low DC-bus voltage?

High DC-bus voltage is commonly associated with rapid deceleration, high inertia, overhauling loads, high incoming mains voltage, an inactive brake chopper or insufficient braking capacity. Low DC-bus voltage may be related to low mains voltage, phase problems, a weak supply or ageing DC-link capacitors.

DC-link capacitors are also important life-limited components inside a drive. As they age, reduced capacitance and increased ESR can increase ripple and internal heating. A recurring DC-bus problem on an older drive should therefore not be treated as a software parameter issue alone; the condition of the power stage and capacitor bank also matters.

Safety warning: Dangerous voltage can remain on the DC link after mains power has been disconnected. Always observe the discharge time specified by the drive manufacturer and verify that the DC-bus voltage has fallen to a safe level with a correctly rated measuring instrument before working on the equipment.

Related OtomasyonAVM topics

Continue with the VFD technical guide, dynamic braking, braking resistors, braking units, servo systems and PLC & HMI automation.