What is temperature measurement?

Reliable temperature readings start with the right method

In everyday language, heat measurement often means temperature measurement. These are different quantities. Temperature describes a system’s thermal state and is expressed in °C or K; heat is energy transferred because of a temperature difference and is expressed in energy units such as joules (J). Reading 80 °C with a temperature sensor does not, by itself, reveal how many joules have been transferred.

In industry, the aim is to determine the temperature of a product, liquid, gas or machine component with the required accuracy and speed. The choice between contact measurement and non-contact measurement depends partly on whether the target is a surface, an internal region or the surrounding air.

Sensors used for contact measurement

Resistance temperature detectors (RTDs) use changes in electrical resistance. A Pt100 is a platinum sensing element with a nominal resistance of 100 ohms at 0 °C. Lead resistance can add to a two-wire reading; suitable three-wire or four-wire measurement circuits reduce its effect. Check the instrument’s connection capabilities as well as the sensor type.

A thermocouple produces a small voltage related to the temperature distribution in a circuit made from dissimilar conductors. Suitable types are used in furnaces, moulds and high-temperature processes. With an NTC thermistor, resistance decreases as temperature rises. Its nominal resistance and characteristic curve must match the instrument. Choosing between a Pt100 and a thermocouple involves stability, response and environmental conditions, as well as maximum temperature.

Liquid-filled, bimetallic and gas-expansion thermometers use other physical effects to indicate temperature. A digital display describes how the result is presented rather than the measurement principle; it does not automatically make the reading more accurate.

A common thermocouple wiring mistake

The thermocouple type selected in the instrument must match the installed sensor. Type K and Type J have different characteristics. Check polarity, cold-junction compensation and the correct extension or compensating cable. Extending the circuit with arbitrary copper cable or hiding a type mismatch with a display offset is not a sound solution.

Infrared thermometers, pyrometers and thermal cameras

Non-contact temperature sensors evaluate thermal radiation from the target. The terms infrared thermometer and pyrometer overlap. Suitable handheld measuring instruments support spot checks, while fixed pyrometers can continuously monitor moving or hot products.

Emissivity, reflected radiation and the distance-to-spot relationship affect the result. Shiny metal can reflect a nearby hot source and produce a misleading reading. A laser marker is for aiming; it does not perform the measurement. A surface reading from an ordinary IR instrument does not directly establish the temperature inside the part.

A thermal camera shows a surface temperature distribution rather than one spot. Its colors represent the selected temperature scale; a red area alone does not prove a fault. Interpret numerical values alongside surface conditions and the operating state of the equipment being compared.

Measurement location and response time

First establish the expected temperature limits and the instrument’s sensor compatibility. Then consider probe diameter, sheath material, immersion depth and chemical resistance. A protective sheath can improve durability while increasing response time. A fast display update does not mean the probe reaches the target temperature equally quickly.

A tank sensor mounted too close to the heater may not represent the bulk liquid temperature. When measuring air, sunlight or radiation from nearby hot surfaces can also influence the result. During installation, choose a location representative of the intended measurement and allow a contact probe to reach thermal equilibrium.

Editor’s note: A display increment of 0.1 °C does not establish ±0.1 °C accuracy; it may describe resolution only. Assess measurement accuracy across the sensor, input circuit, wiring and installation. Measurement uncertainty provides separate information about the result. Calibration establishes measurement deviations; adjustment changes the instrument’s response.

Measurement and control have different roles

The sensor provides temperature information and an indicator displays it. A suitable temperature transmitter can convert the sensor signal to an output such as 4–20 mA. A temperature controller compares the measured value with the setpoint and operates heating or cooling outputs. PID settings cannot correct a wrongly connected sensor or an unsuitable measurement location.

For a suspect reading, first inspect the input configuration, connections, optical or thermal contact and measurement conditions. Then compare against a suitable reference. Check the model’s manual for fault indications and error codes, including sensor-break indications. Identify the cause of a deviation instead of applying the same arbitrary offset to every instrument.

When the required quantity is heat energy

Determining energy gained or lost is different from simply reading a thermometer. In a basic calorimetric calculation, Q ≈ m × c × ΔT can be used when there is no phase change and specific heat is approximately constant. Here m is mass, c is specific heat and ΔT is the temperature change. Account for heat losses and process conditions: the same temperature rise does not mean the same energy for different masses.

Related pages: Temperature controllers / Temperature sensors / Sensor accessories / Temperature control questions