6ES7 134-4NB00-0AB0

6ES7 134-4NB00-0AB0 – Siemens ET 200S 2AI TC High Feature

Series: Siemens SIMATIC DP / ET 200S
Category: Two-channel thermocouple analog input module

Description and applications

6ES7 134-4NB00-0AB0 is a 2AI TC High Feature analog input module for ET 200S stations. It is selected for temperature measurement using thermocouples. Monitoring a furnace, heating zone or process line through a PLC is a typical application to consider.

When selecting a spare, check the full order number, sensor type, terminal module and existing channel settings together. A temperature measurement installation also depends on the sensor wiring and compensation arrangement, so record these before changing the electronic module.

Measurement types and resolution

The two input channels support thermocouple or −80…+80 mV voltage measurement. Resolution is specified as 15 bits plus sign. Supported thermocouple types are B, C, E, J, K, L, N, R, S and T.

Match the configured thermocouple type to the installed sensor label. Select the measurement range and cable for that sensor; using the wrong thermocouple characteristic can produce an incorrect temperature reading. Saving the existing project settings before purchase makes comparison after replacement easier.

Terminal module and cold-junction compensation

The module uses the TM-E15S24-AT screw-terminal or TM-E15C24-AT spring-terminal base. The internal reference junction is located in this terminal module. Enable the relevant channel's reference-junction parameter when using internal compensation.

Thermocouple connections are CH0: 1 (+), 2 (−) and CH1: 5 (+), 6 (−). Verify the terminal-module label and terminal numbers on the installed unit. Also inspect cable shielding, extension-cable suitability for the thermocouple type and the mechanical condition of the connections.

Supply and electrical isolation

The supply is 24 V DC from the ET 200S power module. Maximum L+ consumption is 30 mA; the electronic module is 15 mm wide. Include the other station modules when sizing the panel power supply.

The input channels are not galvanically isolated from each other. They are isolated from the backplane bus and L+ supply. Assess sensor grounding and potential differences against the existing plant connections.

Diagnostics and commissioning

The red SF LED indicates a group fault. Wire-break and underflow/overflow diagnostics are controlled by parameters. Wire-break diagnostics apply to thermocouple measurement. Enabling this function with the ±80 mV voltage range causes a configuration error and prevents the module from starting.

Check each channel separately during commissioning. Review sensor type, polarity, reference-junction selection and filtering. If the reading differs from expectations, compare it with a known test signal at the same input before deciding to replace the module.

Comparison with 4NB50 and 4JB00

6ES7 134-4NB50-0AB0 is the 2AI RTD High Feature version, relevant when researching Pt100 and RTD measurement. 6ES7 134-4JB00-0AB0 is listed as 2AI TC Standard. Compare measurement type, compensation method and terminal compatibility when assessing these products.

Editor's Note

For a used unit, clarify whether the offer includes the electronic module and its terminal base. If a test record is available, ask for the thermocouple type, compensation setting and results for both channels. Measurements at several points using a calibrator provide more useful evidence of condition than a single temperature reading.

PDFs and operating manuals

Visit the Siemens ET 200 PDFs and user manuals section. Technical information appears in the 6ES7134-4NB00-0AB0 data sheet and ET 200S, 12/2004, section 12.17. Consult section 9.10 for the terminal base and Released Modules V7.1 SP3, page 8 for model identification.

Related topics

For control and monitoring, explore PLC and HMI systems, operator panels and SCADA. For system research, see Siemens S7-300, about Siemens ET 200 and ET 200 PROFIBUS and PROFINET.

Other module groups: ET 200 analog input modules · Digital input modules · Digital output modules · Connection modules · Additional modules.

Navigation: Siemens ET 200 · Siemens SIMATIC S7 · Siemens S7 PLC · OtomasyonAVM home