6ES7 138-4GA00-0AB0

Siemens 6ES7 138-4GA00-0AB0 ET 200S 4 IQ-SENSE Sensor Module

Siemens 6ES7 138-4GA00-0AB0 is the 4 IQ-SENSE electronic module for the ET 200S series within the SIMATIC ET 200 family. Each module connects up to four compatible IQ-SENSE photoelectric sensors. Alongside transferring object-detection states to the controller, a suitable configuration allows sensor settings to be managed through the control system.

Sensor compatibility comes first

This module is intended for photoelectric sensors with an IQ-SENSE interface. Each sensor uses a two-wire connection. Check the sensor's exact model and interface specification before selecting a replacement; matching the operating voltage or wire count alone does not establish compatibility.

The background guides to photocells and retro-reflective sensors help explain optical detection. Choosing between reflector-based and diffuse sensing concerns the target and installation. Confirming IQ-SENSE support is a separate interface check.

General descriptions of sink and source wiring or two-wire sensors should not be used as proof that a conventional sensor will work with this module. Compare the sensing function, electrical connection and interface requirements together.

Its place in an ET 200S station

The 4 IQ-SENSE electronics plug into a suitable terminal module, which carries the field connections. A power module supplies the relevant potential group, while the station interface handles communication with the control system.

Record the terminal base, power module and interface-module numbers alongside the electronics-module label. Reviewing the power distribution arrangement and the wider ET 200 system structure helps identify the complete installation before ordering parts.

Suitable terminal modules

Siemens lists TM-E15S24-01, TM-E15C24-01, TM-E15N24-01, TM-E15S26-A1, TM-E15C26-A1 and TM-E15N26-A1 terminal modules. Select the base by its full designation and connection arrangement, rather than its 15 mm width alone.

Electrical and mechanical data

The module receives 24 V DC from the power module. Maximum supply current is 300 mA, and typical power dissipation is 0.85 W. Its dimensions are 15 × 81 × 52 mm, with an approximate weight of 35 g.

The specified maximum sensor cable length is 50 m for both shielded and unshielded cables. Maximum module cycle time is 3.24 ms. This is not the complete machine response time: sensor behaviour, configured timing functions, station communication and the PLC program also influence the result.

Standard and Enhanced configurations

Standard uses one input byte, with the four sensor states represented by individual bits. Enhanced uses four input bytes and four output bytes, providing control and feedback data for sensor adjustment as well as detection states.

The output address space carries commands to the sensors. It does not mean the module contains four physical digital outputs for switching loads. Reading input states and managing sensor settings from the program are different requirements. Check the hardware configuration and program addresses against the intended operating mode.

Teach-in and IntelliTeach

The IQ-SENSE Opto function block supports object-status acquisition, remote teach-in and transfer of sensitivity or distance-setting values using IntelliTeach. When using the function block, the input and output start addresses must match.

Teach-in establishes a sensor setting for the application. IntelliTeach allows a suitable setting value to be transferred from the program. Do not interpret these values as continuous distance measurements in millimetres; their meaning and usable range depend on the sensor.

Commission the sensing arrangement with actual products in their operating position. Different colours, glossy packaging and changing target distances may require separate checks. After adjusting a sensor, verify both target-present and target-absent conditions before returning the machine to production.

Parameters and diagnostics

Available settings cover sensor type, time functions, hysteresis for suitable sensors, synchronization groups and permission to use the sensor's teach-in button. Deactivate unused channels to avoid wire-break diagnostics from unconnected inputs.

Green LEDs indicate channel states, and a red SF LED indicates a group fault. Read the diagnostic information before deciding that the electronics have failed. Review wiring, sensor compatibility, configuration, optical alignment and teach-in status as part of the investigation.

PROFIBUS and PROFINET integration

The ET 200S station's interface module determines its connection to the higher-level network. When assessing PROFIBUS or PROFINET integration, check the interface's full order number, version and project configuration. Review the associated ET 200 connection components as part of the complete station.

Packaging and similar order numbers

The manufacturer's catalogue description specifies a packaging unit of five modules. This must be distinguished from channel count: each individual module supports four IQ-SENSE sensors. Check the delivery quantity stated in the actual quotation or listing separately.

6ES7 138-4GA50-0AB0 identifies the 4SI IO-Link module. Its similar order number does not make it a direct replacement for the IQ-SENSE interface. A change to IO-Link requires the sensors, wiring and software to be assessed together.

PDF manuals and related topics

Visit the Siemens ET 200 manuals page for documentation. For this model, use the 4 IQ-SENSE Module manual, A5E01077604-01, alongside the ET 200S system instructions and the IQ-SENSE Opto function-block information.

For controller-related work, explore Siemens S7 PLCs and SIMATIC S7-300. Include the sensor models and Standard/Enhanced selection in the maintenance record along with the module number.

Editor's note: Start by confirming the sensor's IQ-SENSE compatibility. Four channels on the module or two wires on the sensor are not enough to establish a match. Check the module, sensors and project settings together.

Explore more: Siemens products | SIMATIC S7 | SIMATIC ET 200