6ES7 131-4BD51-0AA0
6ES7 131-4BD51-0AA0 – Siemens ET 200S 4DI 24 V DC / SRC ST
Series: SIMATIC ET 200S
Category: Four-channel, 24 V DC standard digital input module with source inputs
Function and SRC distinction
6ES7 131-4BD51-0AA0 is the 4DI DC24V/SRC ST electronic module for ET 200S within the Siemens ET 200 family. It transfers four field signals to the PLC. Its distinguishing feature among ET 200 digital input modules is the SRC, or sourcing input, circuit.
The manual’s wiring diagram shows activation when a sensor or contact pulls the input towards M, the 0 V reference. This arrangement corresponds to an NPN/sinking sensor output. Here, “source” describes the module input; it does not specify a PNP sensor output. Assess NPN and PNP compatibility from the current path rather than the terminology alone.
Input voltages referenced to L+
Siemens specifies the input levels relative to L+: −30 to −15 V for “1” and −5 to +30 V for “0”. For example, with L+ at 24 V and the input near 0 V, the input measures approximately −24 V relative to L+. This does not require a separate negative power supply.
When replacing a sensor, matching its supply voltage is insufficient. Check the output type, common reference and wiring. An inductive sensor’s detection indicator alone does not establish that the PLC input is connected correctly.
Input delay and sensor selection
Input delay is typically 3 ms in both directions, with a specified range of 2–4.5 ms, and is not parameterizable. Typical input current in state “1” is 7 mA. Two-wire sensors are supported, with a maximum permissible quiescent current of 1.5 mA.
For short pulses from a rotating machine part, do not select the input solely from the sensor’s switching frequency. Consider pulse duration, input delay and PLC scan time together; review ET 200 counter modules where appropriate.
Terminal module and power supply
The electronic module plugs into a suitable ET 200 terminal module. Listed examples include the spring-terminal TM-E15C24-A1 / 6ES7193-4CA30-0AA0 and screw-terminal TM-E15S24-A1 / 6ES7193-4CA20-0AA0. Check terminal availability and the AUX1 arrangement for the selected base.
The 24 V DC supply comes from the power module. Assess the power supply, potential group and sensor connections together. Do not assume that AUX1 carries 24 V; verify its assigned potential against the station wiring plan. Isolate power before modifying field wiring.
Configuration and status indicators
The module occupies one byte, or four bits with supported packing. Verify the actual bit assignment in the project. The station’s ET 200 interface module provides the PROFIBUS or PROFINET connection; this input card has no independent network address.
Each channel has a green status LED. The module has no diagnostic function and no red SF LED. Do not assess a fault solely by looking for an error light on the card; compare the measured input voltage, channel indicator and corresponding program bit.
Dimensions and order quantity
The electronic module measures 15 × 81 × 52 mm and weighs approximately 35 g. Siemens describes a packing unit of five modules. Separately confirm whether a used-item listing includes one module or a five-piece pack, and whether the terminal base is included.
Editor’s Note
Do not choose a replacement solely because it has four inputs and a 24 V rating; the 4BD51 order code and SRC wiring arrangement are decisive. If the sensor operates but the input does not change, check the sensor output and M connection before concluding that the card has failed. For a used module, request verification that all four channels switch correctly in a suitable test setup; one illuminated LED is insufficient.
Manuals and PDF documents
Visit Siemens ET 200 manuals and PDF documents for related documentation. Technical sources: Siemens 4DI DC24V/SRC ST, A5E01077106-01; the model-specific data sheet dated 18 August 2022; and the ET 200S system manual, A5E00515771-06.
Related topics
About Siemens ET 200 · PLCs and modules · PLC and HMI systems · ET 200 terminal blocks
Navigation
Home · Siemens · Siemens S7 PLC · SIMATIC S7 · Siemens ET 200 · ET 200 manuals