6ES5 288-4UA11

Siemens SIMATIC S5 6ES5 288-4UA11 – IP 288 positioning and electronic cam module

The Siemens 6ES5 288-4UA11 (IP 288) reads encoder position on three independent axes. Each axis can be configured for rapid traverse and creep speed positioning or electronic cam control. In positioning mode the module sends digital speed and direction commands to the drive. In cam mode it switches outputs at configured positions. Other S5 positioning modules, including the IP 246, IP 247 and IP 266, serve different applications.

Connections and specifications

Encoder inputs X7, X8 and X9 serve axes 1, 2 and 3 respectively. Maximum count frequency is 500 kHz with 5 V differential RS-422 incremental signals and 50 kHz with 24 V incremental signals. SSI absolute encoders are also supported. When identifying S5 cables and connectors, use sections 9.1 and 9.2 of the manual for the IP 288 pin assignments.

Digital signals and power The 25-pin DIGITAL IN OUT socket carries four digital inputs and four 24 V digital outputs per axis. Siemens labels this socket X5 in the front view (Figure 3.3) and X4 in the pin diagram (Figure 9.3). Before wiring, compare the front-panel marking and section 9.1 pin table with the machine schematic. The specified switching current is 10–500 mA per output. Trace these separately from the addresses of any S5 digital input and S5 digital output modules. The backplane supplies 5 V. The front L+/L− terminals take a separate nominal 24 V DC load supply (20–30 V). Check the S5 system supply and the L+/L− circuit separately during diagnosis.

Programming X3 is the front PG port for COM 288. The Siemens application note shows the 6ES5 734-2BF00 programming cable and 6ES5 966-0AA22 interface. COM 288 can read and archive SYSID, machine data, and cam or target data. The PLC user program communicates via Siemens standard STEP 5 function blocks. See S5 function modules for other task-specific cards on this platform.

CPU and rack compatibility

For the S5-115U CPU family, Siemens lists the 941B, 942B, 943B and 944B. The IP 288 uses one slot with an adapter casing. Section 4.2 gives the slot layouts for the S5 racks. Use slots 0–2 on the CR 700-0LB or slots 0–5 on the CR 700-2 and CR 700-3.

For the S5-135U, the manual lists CPU 922 (revision 9 and later), CPU 928 and CPU 928B. The 6ES5 135-3UA11 and 6ES5 135-3UA21 are examples of this rack family. For the S5-155U, Siemens lists CPU 946/947. The card occupies two standard slots in the 135U and 155U. If an expansion rack uses interrupts, check the manual’s IM 307 and IM 317 interface module pairing. The fibre-optic IM 307 version is a separate reference for identifying existing hardware.

Editor’s note

Before removing the card, use COM 288 to archive SYSID, machine data and the active cam or target sets. Record the slot, base address and firmware revision.

When buying used, ask to see the 6ES5 288-4UA11 label, rear connectors and X7–X9 sockets. Ask for a COM 288 readout and a position count on every axis you plan to use, where bench testing is available.

If RUN is lit and the outputs stay off, read the EXF record. For error 1, start with the load supply at L+/L−. Isolate power before checking F1 and F2 as shown in the manual.

EXF 9 points to the 5 V differential encoder signal line. For EXF 10, check A/B signals on an incremental encoder or the data frame on an SSI encoder, and confirm the encoder type set in COM 288.

If COM 288 cannot go online, start with X3, the PG cable and the interface part number. Trace the CPU programming connection and the IP 288 PG connection separately on the schematic.

Isolate the rack and load supplies before replacing the card. Verify counting direction, the reference and limits before enabling motion. Make the first move at low speed under controlled test conditions.

Siemens PDF documents

+ IP 288 / COM 288 manual – 6ES5 998-5SF21 (EN)

+ IP module programming connections – Siemens APPnote 249, p. 2 (EN)

+ SIMATIC S5 shared PDF archive

Related topics

+ About Siemens S5 PLC

+ SIMATIC S5 special modules

Navigation

+ S5 positioning modules

+ SIMATIC S5

+ Siemens S5 PLC

+ Used Siemens equipment