6ES5 435-4UA12

Siemens 6ES5 435-4UA12 — 16-Channel, 24–60 V AC Digital Input Module

6ES5 435-4UA12 is a 16-channel, 24–60 V AC digital input module for Siemens SIMATIC S5 S5-135U/155U systems. This model in the S5 digital input range has two galvanically isolated groups of eight inputs. The rated AC input frequency is 47–63 Hz.

The board transfers suitable AC control signals to the SIMATIC S5 CPU. Do not treat it as a 24 V DC input board. Dimensions are 40 × 255 × 195 mm, with an approximate weight of 0.55 kg; check these together with the existing rack and front wiring arrangement.

Input thresholds and current

Logic “0” is specified at 0–15 V AC and logic “1” at 20–72 V AC. Typical input current is 15 mA at 48 V AC and 20 mA at 60 V AC; typical input resistance is 3 kΩ. A connected sensor or relay circuit must meet these voltage and current conditions.

Two-wire BERO sensors

For two-wire BERO proximity switches, the specified input current is no more than 5 mA at logic “0” and at least 10 mA at logic “1”. Check the sensor’s AC voltage rating and off-state leakage together. Two-wire construction alone does not establish compatibility.

Isolation groups and field wiring

Each eight-input set forms an isolated group. Follow the diagram’s 1N and 2N group references correctly. Distinguish group returns from the grounding arrangement; when a whole group disappears, inspect its common connections first.

Maximum S5 field-cable lengths are 600 m unshielded and 1000 m shielded. Assess cable capacitance, interference and leakage voltage separately. Measure between the relevant input and its own group reference.

Response times and pulse frequency

The typical rising-edge delay is 5 ms, with a 2–15 ms range; the typical falling-edge delay is 20 ms, with a 10–25 ms range. Maximum pulse-train input frequency is 20 Hz. Assess this separately from the 47–63 Hz AC signal frequency.

Cooling and simultaneous inputs

The coincidence factor is 100% with a fan. Without a fan, the manual specifies 75% at 60 V, with 100% up to 35 °C and 100% at 30 V also listed. Assess cabinet temperature, input voltage and active-channel count together.

Power dissipation at rated operation is 3.5 W at 24 V and 18 W at 60 V. Typical consumption from the internal 5 V system supply is 100 mA. Operation at a low AC voltage does not imply a low heat load under every condition.

F+/F− enable jumper and X20

The F+/F− enable connection uses a jumper in the front connector. Inserting X20 makes the enable input active; this is the factory setting. Record the front jumper and X20 position before replacement, then compare them with the exact model’s diagram. Do not change the enable arrangement by trial and error during fault finding.

Addressing and fault tracing

Compare the starting address and bit sequence of the two input bytes with the PLC program. In the appropriate programming software, ensure the monitored bit corresponds to the channel being measured. Interpret the green channel indicators alongside measurements and program monitoring.

During troubleshooting, check input voltage, group reference and enable jumper together. If the input reads correctly, follow the logic conditions affecting the expected output and the S5 system operating state. Isolate field and system power before disconnecting wiring.

Comparison with related models

The 6ES5 436-4UA12 has 16 inputs and 6ES5 436-4UB12 has eight inputs at 115–230 V AC. The 6ES5 431-4UA12 has 16 inputs at 24–60 V DC, while the 6ES5 430-4UA13 has 32 inputs at 24 V DC. Similar order codes do not establish identical input types or wiring arrangements.

Editor’s note

Start with the AC marking. Do not assume a familiar “24 V input” means the same connection as a DC board. Matching the sensor and control-circuit voltage type at the start can save a long fault search later.

If eight inputs disappear together, check before replacing the board. Inspect that group’s N reference, terminal tightness and field connections. One common connection problem can make eight channels appear to have failed at once.

Do the heat assessment for a 60 V installation. The manual gives 18 W power dissipation and a 75% coincidence factor without a fan at this voltage. A stopped fan or blocked airflow in an older cabinet can change the situation considerably.

Photograph the F+/F− jumper and X20 before removing the old board. A missing enable connection can be mistaken for a board fault. Recording the setting and checking the diagram is more dependable than moving jumpers by trial and error.

When buying a used Siemens 435-4UA12, have all sixteen channels tested with suitable AC signals. Check logic “0” and “1” in both groups. A few working lights are encouraging; seeing every channel respond is much more reassuring.

OtomasyonAVM resources and PDFs

Siemens S5 PDF page · S5 digital input modules · S5 racks and expansion units. The exact 435-4UA12 model is covered in the S5-135U/155U System Manual, §8.4.6, pp. 8-42–8-43. The English document is C79000-G8576-C199-07; the German document is C79000-G8500-C199-07.

Related topics

436-4UA12 · 436-4UB12 · 431-4UA12 · 430-4UA13 · Two-wire sensors.

Navigation

S5 digital input modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens.

Siemens and external references

Siemens S5-135U/155U System Manual — German; §8.4.6, pp. 8-42–8-43: 435-4UA12 specifications, cooling limits, enable jumper and wiring diagram.