6ES5 943-7UA11

Siemens 6ES5 943-7UA11 — S5-115U CPU 943 with 16 KB RAM and one PG port

Siemens 6ES5 943-7UA11 is the S5-115U CPU 943 central processing unit in the Siemens S5 family. The manufacturer’s data sheet specifies 16 KB RAM and one programmer port. In a SIMATIC S5 installation, it executes the user program, evaluates inputs and generates output commands.

Do not assume identical memory and interface specifications to the 6ES5 943-7UB11 or 6ES5 943-7UB21. When comparing nearby numbers such as 6ES5 943-7UA21 and 6ES5 943-7UA22, record the complete suffix and board version as well.

Internal RAM and external memory limits

The 16 KB internal RAM differs from the 48 KB total user area possible with an external submodule. When checking S5 memory submodules, consider usable capacity rather than chip capacity alone. The manual specifies 40 KB EPROM plus 8 KB internal RAM with 6ES5 375-0LA61.

Different memory types, such as the 6ES5 375-0LA41 EPROM and 6ES5 375-0LC41 EEPROM, also require different programming and erasing methods. Verify the submodule number, programming number and CPU-specific capacity limit against the applicable table. Keep the memory identification together with the actual program backup.

Execution time and program resources

The original S5-115U manual gives approximately 1.6 µs per bit operation for this exact number. Resources include 128 timers, 128 counters and 2048 flag bits. An instruction time is not the complete program scan time.

When reviewing the STEP 5 program, compare logic shown in Ladder or function block representation with actual input changes and output responses. Record measured scan time together with the program version and machine conditions under which it was measured.

PG connection and communication checks

The 15-pin TTY interface supports PG, operator-panel or suitable SINEC L1 connections. Select the S5 programming cable against the port’s own wiring diagram. A matching plug does not make an ordinary RS-232 cable suitable.

Do not plan connections as though this model has a second port. Record the interface connection and communication arrangement alongside the existing cable labels. If the single port is already connected to another device, assess the machine impact of disconnecting it before intervention.

Power, addressing and maintenance preparation

Photograph the rack arrangement, power supply and installed modules before removal. Compare digital input, digital output and analog module addresses with the existing project. A CPU replacement is not a reason to change addresses or module settings by guesswork.

During PLC troubleshooting, record LED indications and information available through the PG first. OVERALL RESET erases RAM contents. Do not use it as a trial step without a verified program backup and recovery method. Include the battery connection and installed memory contents in the check plan.

Editor’s note

When buying a used Siemens CPU, a visible “943” marking is insufficient: read the complete 7UA11 suffix. Do not assign a later version’s specifications to this board. Request photographs of the front panel and rear connectors.

When discussing memory capacity, establish whether the figure refers to internal RAM, the installed submodule or total usable space. A larger number in a listing is not enough; identify where the program is stored and what backup is available.

A lit RUN indicator does not establish a complete test. Request separate PG connection, program read/load and memory checks on a suitable bench. Do not assume an untested function is serviceable.

Back up the existing machine program before removing the board and check that the file opens. A machine name on an EPROM label does not establish that its contents are current. Investigate later program changes as well.

If the PG connection is intermittent, check the cable, adapter, contacts and connection settings before condemning the CPU. Record whether moving the cable changes the symptom, and compare with a known-good connection under the same conditions.

For S5 maintenance, a clear record helps the next repair. Keep the CPU number, board version, installed memory, cable type and test results on one form. The next technician should not have to guess what changed or which checks were completed.

OtomasyonAVM resources and PDFs

+ Siemens S5 PDF archive: system and module documentation. The manufacturer manual for this original CPU generation is linked below.

+ 6ES5 943-7UA11 model page and second-hand Siemens S5 models: the CPU and related system components.

Related topics

+ 6ES5 943-7UA21 · 6ES5 943-7UA22 · 6ES5 943-7UB11 · 6ES5 943-7UB21: different family members; direct interchangeability should not be assumed.

+ S5 memory products · S5 cables · PLC debugging: memory, connections and maintenance.

Browse SIMATIC S5

Product page · Siemens S5 · SIMATIC S5 · Used Siemens equipment

Siemens and external references

+ Siemens 6ES5 943-7UA11 data sheet — manufacturer document hosted by JC-Electronics: 16 KB RAM, one programmer port.

+ Siemens S5-115U CPU 941/942/943/944 Gerätehandbuch — 6ES5 998-0UF12, Ausgabe 03, German. Chapter 2 and Table 2.8: memory; page 15-14: specifications for this exact number. Document: GWA 4NEB 811 6000-01b.