6ES5 942-7UF14
Siemens 6ES5 942-7UF14 – CPU 942F for the S5-115F Failsafe System
Siemens 6ES5 942-7UF14 is a CPU 942F module for the S5-115F failsafe control system in the SIMATIC S5 family. Assess this S5 CPU together with the hardware and software configuration of the installed F system. Replacement checks must include the partner subunit, program and system parameters as well as the processor number.
942F, standard 942 and 942H
6ES5 942-7UA13 belongs to standard S5-115U, while 6ES5 942-7UH11 belongs to S5-115H. UF, UA and UH suffixes do not identify the same product. 6ES5 942-7UF12 and 6ES5 942-7UF15 are also separate F versions. Do not select replacements from similar numbering alone; compare the installed system’s documentation and configuration scope.
Documentation scope for this model
Siemens directs users to manual 6ES5 998-1UF23 for 942-7UF13 and 942-7UF14. The main hardware description in the linked 1UF25 set covers 7UF15. Its RAM, current and timing figures have therefore not been assigned to 7UF14 here. Use 1UF23 and the relevant product information for definitive hardware ratings.
STEP 5 and COM 115F configuration
Preserve the STEP 5 program and COM 115F configuration together during PLC programming. Siemens explicitly confirms that COM 115F version 3.2 can configure 942-7UF14; select the CPU identifier matching the installed unit. Record the S5 memory module numbers and contents alongside the software and project files. Identify the machine and version associated with each backup.
Subunit, chassis and connection checks
List the installed S5 supplementary equipment, racks and chassis, power supply and subunit pairing. Label interface hardware and connecting cables before removal. Do not assume that fitting the replacement CPU automatically establishes correct system parameters; compare labels, revisions and project records.
SINEC L1 message mode
For industrial communication, the Siemens comparison table lists 115F-14 message mode for 942-7UF14 and 7UF15; it includes protective specification of the destination slave number. 115F-15 mode is assigned to 7UF15. Establish the role of the communications hardware and SINEC L1 components such as CP 530 separately, then compare partners, message mode and mailbox arrangement with the existing project.
Diagnostics and replacement records
During PLC debugging, assess CPU indicators, COM 115F diagnostics and subunit states together. For Siemens S5 PLC maintenance, record the existing fault before deciding which part to replace. Complete commissioning by rechecking the application’s safety functions against its own test plan.
Editor’s Note
When buying used Siemens equipment, obtain a clear view of 942-7UF14 and the revision on the label. A generic 942 description is insufficient. Record the partner subunit number and assess the part within its intended system.
A program block backup alone should not be treated as the complete service record. Keep the COM 115F configuration, memory module details and last test records available. Identify the last working application by date and machine name.
Do not transfer 7UF15 manual ratings automatically to 7UF14. Siemens identifies a separate document for this version. Check memory capacity or response time in the correct edition rather than estimating.
Reaching RUN does not finish the job. Verify subunit operation, communication and the relevant safety functions against the test plan. Keep records of a board’s bench operation separate from validation of the installed machine system.
Capture diagnostics before clearing memory or changing parameters. Do not mask the fault by bypassing protection; establish which condition stopped the system. Record the replacement number, revision and test result clearly for the next technician.
OtomasyonAVM resources and PDFs
+ Shared SIMATIC S5 PDF archive – S5-115 PDF files. Check CPU coverage on the cover and in the introduction; Siemens identifies 6ES5 998-1UF23 as the principal reference for 7UF14.
Related topics
+ 6ES5 942-7UF12 · 6ES5 942-7UF15 · 6ES5 942-7UH11 · 6ES5 942-7UA13 · 6ES5 530-7LA12
Browse SIMATIC S5
+ S5 CPU models · S5 memory modules · S5 racks and chassis · S5 communications modules · Siemens SIMATIC S5
Siemens and external references
+ Siemens S5-115F Manual, Volume 1 – EWA 4NEB 811 6148-02. Introduction: UF14 reference to 1UF23; Table 7-6: UF14/UF15 message modes. Main hardware coverage is UF15.
+ Siemens S5-115F Manual, Volume 2 – EWA 4NEB 811 6149-02. Chapter 1, printed page 1-7: COM 115F 3.2 and UF14 CPU selection. It does not replace 1UF23 for all hardware specifications.