6ES5 526-3LA01
Siemens 6ES5 526-3LA01 SIMATIC S5 CP 526-I Monochrome Visualization Processor
The Siemens 6ES5 526-3LA01 is a CP 526-I communications processor that displays machine screens and fault messages on SIMATIC S5 systems. This version drives a monochrome monitor and requires forced-air cooling. The front panel has one BNC output for 75 Ω BAS composite video and a 15-pin, 20 mA TTY port for a programming device or process keyboard. Siemens lists the CP 526 family for specified slots in S5-115U, S5-135U, S5-150U and S5-155U racks.
The module exchanges data with the S5 CPU over the backplane. Operators use the process keyboard to call up stored displays and enter setpoints where the application allows. The closely related 6ES5 526-3LA11 also requires forced air and has a colour RGB monitor interface.
Monitor and programming connections
The single BNC carries both picture and sync. Siemens specifies a 0.7 V picture component and a 0.3 V sync component into 75 Ω. Check the monitor for a BAS input and verify the low-resolution setting. When documenting the S5 cabling, identify the monitor coax and the PG/keyboard cable separately.
The programming device (PG) and the process keyboard share one 15-pin socket. The module detects the connected device and selects the operating mode. The specified TTY interface range is 50 to 9,600 bit/s. Match the cable and current-loop wiring to section 3.10.3 of the manual when selecting S5 interface hardware.
Rack, slot and addressing
On an S5-115U, the CP 526 requires an adapter housing in CR 700-2 S5 racks such as the 6ES5 700-2LA11 and 6ES5 700-2LA12. Slot requirements for the S5-135U, S5-150U and S5-135U/155U central rack depend on the hardware configuration. Match the installed rack to Table 3-1 in the Siemens manual.
For data exchange with the PLC, check the X7 page-frame address against the SSNR parameter of the CPU’s SYNCHRON block. Record the EPROM or RAM submodule before replacement. It holds the application displays and their associated runtime information.
Related order numbers and cooling options
The 6ES5 526-3LB01 is the naturally cooled monochrome version. The 6ES5 526-3LF01 and 6ES5 526-3LG01 are monochrome S5-DOS variants. Their colour counterparts are the 6ES5 526-3LF11 and 6ES5 526-3LG11. Match the video output, cooling method and hardware version when selecting a spare.
The 6ES5 526-3LA21 and 6ES5 526-3LA22 are expansion boards. Siemens describes graphics expansion for the colour CP 526.
Editor’s note
Photograph the label and front panel together. Capture the 526-3LA01 suffix, single BNC output and memory submodule label.
Inspect the fan assembly. Check the installed fan’s label and the rack mounting hardware. Use the rack and supply details when comparing fan assemblies such as the 981-0HA11 and 981-0HA21.
Back up the screen project before removal. The RAM submodule receives battery backup through the backplane. Removing either the CP or the RAM can erase the application held in RAM. Switch off the rack before replacing the module.
Check video and PLC data separately. If the display is visible but values stop updating, check the CP’s RUN/STOP position and page-frame address. If the screen is blank, check the monitor input, coaxial cable and CP indicators.
Photograph the jumper settings. Siemens specifies X10/X14 for low resolution and X17 in position B for monochrome operation. During commissioning, call up a process screen and compare a live value with the PLC data.
OtomasyonAVM resources and PDFs
About SIMATIC S5 PLC systems · S5 communications modules
OtomasyonAVM SIMATIC S5-115 PDF manual archive
Related topics
CP 526-I colour 3LA11 · CP 526 monochrome, naturally cooled 3LB01 · CP 526-2 monochrome 3LF01
Browse SIMATIC S5
Siemens SIMATIC S5 · S5 communications modules · S5 racks
Siemens and other external references
Siemens COROS CP 526 Communications Processor Manual (English PDF) (Chapter 3 covers slots, addressing and connections)
ADEGIS Siemens 6ES5 526-3LA01 technical listing · PLC Hardware CP 526-I order number listing