6ES5 526-3LG01
Siemens 6ES5 526-3LG01 SIMATIC S5 CP 526 Monochrome Video Processor
The Siemens 6ES5 526-3LG01 is a naturally ventilated CP 526 base module for monochrome monitors, configured under S5-DOS. It displays PLC data at the operator station in a SIMATIC S5 installation. The CP 526 family manual covers mounting in S5-115U, S5-135U, S5-150U, and S5-155U systems. The monochrome configuration uses one BNC connector for 75 Ω BAS video and a 15-pin, 20 mA TTY port for the process keyboard or programming device.
At the machine, this S5 communications module displays process screens, live PLC values, and fault messages. The operator can call up screens and enter setpoints from the process keyboard where the application allows it. The 3LG01 is monochrome. The naturally ventilated 6ES5 526-3LG11 is the color-monitor version.
Where do the monitor and keyboard connect?
The front-panel BNC carries the monochrome BAS signal, combining picture and sync on one line. The Siemens family manual specifies a 0.7 V picture component and a 0.3 V sync component into 75 Ω. When selecting a monitor and an S5 connecting cable, check the input signal, termination, and scan timing together.
Siemens specifies the 640 × 234 pixel low-resolution setting for the monochrome CP 526. The standard operator screen has 80 columns and 24 lines, with 22 process lines and one line each for messages and commands. Color attributes appear as shades of gray on the monochrome screen.
The process keyboard or PG plugs into the 15-pin front connector. Both use the serial 20 mA TTY current loop. Select the cable for the device being connected. The process keyboard draws its 24 V DC supply from the PLC rack.
Where are the screens stored and how does the CPU exchange data?
Screens and message text configured in COM GRAPH are stored on the CP’s EPROM or RAM memory module. The PLC passes changing process values to the CP over the backplane. RAM is battery-backed through the rack. Back up the screen project before removing the board or RAM module.
The SSNR setting must match the CP’s page number. In STEP 5, SYNCHRON establishes communication between CPU and CP, while SEND-ALL and RECEIVE-ALL handle data exchange. In an S5-135U with a CPU 922 or CPU 928, check the block calls in the existing STEP 5 project.
What determines the rack and expansion options?
The permitted slots depend on the S5 rack. In an S5-115U, the CR 700-2 requires an adapter casing. For the ER 701-3 or CR 700-3, check the slot and interface conditions in Table 3-1 of the manual.
On CC 135U/155U central racks and EU 185U expansion units, use the slot list for the specific PLC configuration. Keep the air path clear around the naturally ventilated board. Switch off rack power before inserting or removing the board or memory module.
The 6ES5 526-3LA21 and 6ES5 526-3LA22 are separate CP 526 expansion boards. The Siemens family manual describes the expansion arrangement for trend curves, bar graphs, and enlarged values with a ventilated color base module.
Editor’s note
Read the 3LG01 suffix on the label when sourcing a spare. The 3LB01 is also a naturally ventilated monochrome CP 526. Match the installed memory module and COM GRAPH project to the full replacement part number.
The 3LA01 and 3LF01 are monochrome variants that require forced ventilation. Check the cabinet fan and rack layout before selecting either variant.
Before removing the board, record the rack slot, address jumpers, and memory module label. With RAM fitted, back up the working screen project while the board is still in place.
If the screen is blank, start with monitor power, the selected video input, and the BNC connection. If the picture rolls or loses sync, check the monitor’s scan settings and 75 Ω termination.
If the screen opens but process values stop updating, check the CP’s RUN position, the SSNR value in STEP 5, and the CPU-to-CP data handling blocks. Read the RUN, STOP, and CP Fault LEDs together using Table 3-2 of the manual.
OtomasyonAVM resources and PDFs
Browse the SIMATIC S5 communications modules and the Siemens S5 PLC overview for related hardware.
For system documentation, see the SIMATIC S5-115 PDF archive and the S5-135U/155U central rack and manual page.
Related topics
CP 526 3LG11 color version, CP 526-2 3LF01 monochrome version, and CP 526 3LA22 expansion board.
Browse SIMATIC S5
SIMATIC S5 family › S5 communications modules
External references
Siemens COROS CP 526 communications processor manual (English PDF).
6ES5 526-3LG01 part-specific technical listing · Siemens product list showing the 3LG01 and 3LG11 variants (PDF).