6ES5 465-7LA12

Siemens 6ES5 465-7LA12 | SIMATIC S5 Analog Input Module, 8/16 Channels, Voltage, Current and Pt100

The Siemens 6ES5 465-7LA12 is a non-isolated analog input module for SIMATIC S5-115U and S5-115H systems. It can be configured for 8 or 16 voltage/current inputs or 8 four-wire Pt100 inputs. Plug-in 498 range cards set the measuring range for groups of four inputs. With the appropriate hardware settings, it measures ±50 mV, ±500 mV, ±1 V, ±5 V, ±10 V, ±20 mA and 4–20 mA signals.

In service, the module converts analog signals carrying pressure, level or temperature information into digital values at its measurement inputs. The voltage difference between the sensor reference potential and the central grounding point must remain within ±1 V. The related 6ES5 460-7LA12 has eight galvanically isolated inputs. Consider both channel count and field reference potentials when choosing between these modules.

Selecting the measuring range cards

Depending on the channel configuration, the module uses two or four range cards. Each card adapts four input signals to the module’s measuring level. Match the range card number to the main module’s 50/500 mV base setting and the selected measurement mode.

+ The 6ES5 498-1AA11 through-connection card supports ±50 mV, ±500 mV or Pt100 measurement with the corresponding selector settings.

+ At the standard 500 mV base setting, the 6ES5 498-1AA21 provides ±1 V, the 6ES5 498-1AA61 provides ±5 V and the 6ES5 498-1AA31 provides ±10 V.

+ The 6ES5 498-1AA41 shunt card provides a ±20 mA input range at the standard setting.

+ For 4–20 mA measurement, the 6ES5 498-1AA51 two-wire transducer card and the 6ES5 498-1AA71 four-wire transducer card serve different wiring arrangements.

Front connector, reference potential and Pt100 wiring

Field wiring connects through a 46-contact S5 front connector. Options include the 6ES5 490-7LB21 screw-terminal connector, the 6ES5 490-7LA11 crimp connector supplied with contacts and the 6ES5 490-7LA21 crimp connector supplied without contacts.

In voltage/current mode, channel 0 uses 3 (M0+) and 4 (M0−), while channel 15 uses 45 (M15+) and 46 (M15−). Check the Mext connections at pins 13 and 37 against the system’s central reference wiring. For Pt100 measurement, use the manual’s four-wire diagram to match the measuring leads and sensor excitation connections.

The logic section takes 5 V from the system bus and typically draws 150 mA. The external 24 V DC connection supplies two-wire transducers or supports the circuit for disabling the wirebreak test current. Its permitted range is 20–30 V DC.

Channel configuration and scan time

The module’s I and II mode selectors set the measurement type, 8/16-channel operation, 50/60 Hz selection, cyclic or selective sampling, digital representation and wirebreak monitoring. Pt100 operation requires the 500 mV base setting and the four-wire/eight-channel configuration. Compare the settings with the table for the exact 7LA12 order number.

Integration time is 20 ms at 50 Hz and 16.6 ms at 60 Hz. With nominal values applied to all inputs, Siemens specifies a complete cyclic scan at 50 Hz of 480 ms for eight inputs or 960 ms for sixteen inputs. Consider this measurement update interval alongside the control program’s scan time.

Addressing and reading values in STEP 5

Preserve the module’s slot and address record in the rack layout, for example in a CR 700-3 central rack. With variable addressing through the S5-115U IM 306, a 16-channel analog module can start at 128, 160, 192 or 224. It occupies 32 bytes in this configuration.

In a CPU 943 or CPU 944 program, each input is read as one word. Its channel address is start address + 2 × channel number. Selectable representations are 12 bits plus sign or 13-bit two’s complement. When checking FB 250 scaling or direct peripheral reads, also evaluate the F, OV and activity status bits.

Editor’s note

Record the complete label. Check the 6ES5 465-7LA12 order number and hardware revision before replacement. In particular, compare Pt100 fault behaviour with the manual for that revision.

Photograph the range cards in position. Record the 498 number for each four-input group, the I/II selector positions and the measuring range used in the program.

Measure reference potential differences. If several channels drift together, inspect the sensor reference connections. Verify the ±1 V reference potential limit in the installation.

Allow for the update interval. When applying a new value with a calibrator, allow for a sixteen-channel scan taking 960 ms under nominal conditions.

Match wirebreak monitoring to the measurement circuit. The defined wirebreak test uses the 1AA11 through-connection card and appropriate selector settings. For Pt100 circuits, inspect the measuring leads and the S+ excitation lead together. Assess current-loop faults according to the installed shunt card and program logic.

OtomasyonAVM resources and PDFs

+ Siemens SIMATIC S5 systems and module overview

+ OtomasyonAVM S5-115 manuals and PDF archive

+ SIMATIC S5-115H system manual — 6ES5 465-7LA12 wiring diagram and specifications

+ SIMATIC S5-115H system manual — 465-7LA12 mode selectors and measurement settings

Related topics

+ 6ES5 465-7LA11 analog input module

+ 6ES5 465-7LA13 analog input module

+ 6ES5 460-7LA12 eight-channel isolated analog input

Category navigation

+ SIMATIC S5-115U system family · S5 analog modules

Siemens external references

+ Siemens SIMATIC S5-115U system manual — addressing, analog inputs and FB 250

+ Siemens SIMATIC S5-115H system manual — exact 6ES5 465-7LA12 technical specifications