6ES5 241-1AF12

Siemens 6ES5 241-1AF12 IP 241 SSI Absolute Encoder Interface Card

The 6ES5 241-1AF12 is the single-channel synchronous serial (SSI) absolute encoder interface for IP 241 in SIMATIC S5. Siemens calls this version Absolute 4. The IP 241 base module in the S5 positioning range uses the measured position to evaluate thresholds defined in the project.

Fit one 1AF12 to one channel of the two-channel 6ES5 241-1AA12 base module. For machines with the earlier 1AA11 base module, check the hardware and firmware against Section 7.3. The base module fits in the S5 rack and provides the front connector for each encoder channel. Trace SSI wiring separately from the S5 digital inputs.

SSI wiring and resolution

The card sends the clock on LOOP OUT and receives position data on LOOP IN. Siemens specifies twisted-pair cabling for the base module’s 50-pin Sub-D connector and RS-422/RS-485 interface. S2 selects the receiver for differential encoder signals or the optocoupler current loop. Check the S5 interface wiring against the pin table in Section 7.3.7.

The card evaluates up to 20 position bits in Gray or binary mode. The base module’s binary-to-BCD conversion is limited to 17 bits. For a replacement encoder, check its encoder resolution, code format and supply voltage together. If IP 241 powers the encoder, Siemens specifies an external 24 V DC supply at the base module’s Faston connection. Check the encoder’s own supply requirement against Section 7.3.2.

S5 program and spare selection

Siemens documents IP 241 for S5-115U, S5-135U, S5-150U/S and S5-155U. In the S5 PLC project, FB 156 loads startup parameters. FB 157 or FB 158, which uses a working data block, reads or controls the module during operation. For a CPU 928 installation, check the S5 function module data block against the CPU version and existing project.

Other IP 241 cards cover different encoder types. The 1AB11 is incremental, the 1AC11 accepts parallel Gray/Excess-3 and the 1AD12 accepts parallel BCD/binary. The 1AE12 is the analog encoder interface, while the IP 246I is a separate positioning module. Match the 1AF12 order number, base module and encoder interface when choosing a spare.

Editor’s note

Record the original settings before swapping hardware. Follow the plant isolation procedure. Photograph the BR1 code jumper, S2 input selector and S5.1/S5.2 switch settings.

If position is missing, check power and each signal pair. Once encoder power is confirmed, trace the clock output and returning data against Section 7.3.7. Check the SENSE leads against Section 7.3.5.

For a fault on startup, check the TB parameter. Power cycling or a software reset restores the default TB. Verify that the PLC reloads the correct number of clock pulses for the selected channel.

If the reading overflows at a repeatable position, check VZ. A lit synchronization LED with VZ=1 indicates overflow. Check the encoder resolution and binary-to-BCD setting.

If the synchronization LED is on with VZ=0, check the control bit. With control-bit evaluation enabled, compare S4 and the S1 polarity setting with the encoder’s data frame.

Ask for a position-reading test when buying used. Request a test with an IP 241 base module and SSI encoder at two known positions and again after restart.

To offer this card for sale, send the full order number, card and connector photos, and any test result to otomasyonavm@gmail.com.

PDF manuals and pin assignment

+ Siemens IP 241 equipment manual (English PDF) · SSI wiring §7.3.5, fault diagnosis §7.3.6, pin assignment §7.3.7. See p. 8-9 for 1AF12.

+ Siemens IP 241 equipment manual (German PDF)

+ Shared S5 PDF archive

Related topics

+ 6ES5 241-1AA12 IP 241 base module

+ What is an absolute encoder?

+ About Siemens S5 PLC

Navigation

+ S5 Positioning Modules

+ SIMATIC S5

+ Second-hand Siemens