6ES5 758-0AA11
Siemens 6ES5 758-0AA11 — TS 758H teleservice unit
Siemens 6ES5 758-0AA11 is identified as the TS 758H teleservice unit, a communication device used in telephone-based remote-service arrangements for SIMATIC S5 PLCs. Its role is within the service connection between the programming device and the target SIMATIC S5 system. Siemens’ TK 858 commissioning instructions explicitly refer to the earlier TS 758 arrangement and communication with TS 758H units.
Assess it as part of the complete installation: programmer, target CPU, connecting cables and line-side equipment. Identify the role of each item of S5 communication hardware, and establish which PLC programming or diagnostic task the existing arrangement supports.
Programmer connection and line-side checks
First confirm a working local connection to the target CPU, then investigate the remote-service chain. Record the ends of the S5 programming cable, port labels and interface hardware. Connector shape alone does not establish pin assignments or electrical compatibility.
For an S5-90U or another S5 CPU group, use the complete CPU number when checking the connection. A shared family name does not establish that every installation uses the same programmer port and cable.
Supply voltage, pin assignments and data rate must be matched to the TS 758H label and its original documentation. Do not apply TK 858 DIP-switch settings or electrical specifications as TS 758H instructions. Photograph the settings of an existing working installation before changing them.
Software and information at the remote end
Record the STEP 5 release and project files on the programming computer. A software order such as the 6ES5 894-0MA02-0UG4 STEP 5 upgrade package is separate from the communication hardware; software suitability requires its own check.
When reviewing a project through a ladder diagram or function block diagram, establish which addresses connect the displayed logic to the field equipment. Establishing communication and selecting the correct project and CPU are separate checks.
Compare monitored digital inputs with the physical sensor states, and compare digital outputs with the response of their loads through the person on site. For analog modules, check raw-value units and scaling; for combined I/O groups, verify each channel’s role against its hardware documentation.
Distinguishing TK 858 and PG-MUX roles
The documentation for the 6ES5 858-0AA11 TK 858 helps establish the historical service context of the TS 758 family. It is neither the original 6ES5 758-0AA11 operating manual nor evidence that the two devices are unconditionally interchangeable.
The 6ES5 757-0AA11 PG-MUX is a separate programmer-multiplexer product. Even where these items appear in one installation, record their roles and connections individually. Similar order numbers do not establish identical functions or cabling.
Editor’s note
With older communication equipment, preserve the working arrangement before investigating it. Photograph every cable end, label and setting. Then change one item at a time; changing several items together makes it harder to identify the actual cause.
If the CPU cannot be reached locally, resolve that first. In PLC troubleshooting, a working local connection is a useful baseline before investigating the remote link. Start with a known-good programmer, suitable cable and correct CPU selection.
For a used unit, an illuminated indicator is insufficient evidence. Where possible, request a demonstration with suitable equipment at the other end of the link. Record completed and outstanding tests separately; a missing cable can be harder to source than the device itself.
Before making remote changes, preserve the documented project and existing program. Do not treat the program in an S5 memory module as a substitute for the computer’s project files. Keep a reliable recovery copy before editing.
For intermittent communication, record the stage at which it fails instead of repeatedly restarting the same operation. Does the failure occur at startup, while establishing the connection or while reading data? That distinction helps narrow the cable and line-side checks.
In S5 maintenance, remote access is useful, but an informed person at the machine remains essential. Coordinate the work with them. Afterwards, document the changes, final settings and complete connection arrangement that worked.
OtomasyonAVM resources and PDFs
+ About Siemens S5 PLCs and S5 communication modules: system and communication-hardware background.
+ Siemens S5 manuals and PDF archive: CPU and system documentation. Specifications for another model must not replace the original TS 758H information.
Related topics
+ 6ES5 858-0AA11 — TK 858 telecommunications unit: a separate device whose Siemens documentation references the TS 758 family.
+ 6ES5 757-0AA11 — PG-MUX programmer multiplexer: programming-connection hardware with a different role.
+ S5 cables and connectors and the STEP 5 PC upgrade package: separate cable and software considerations.
Browse SIMATIC S5
S5 expansion products · S5 communication modules · Siemens S5 PLCs · Second-hand Siemens products
Siemens and external references
+ Siemens TK 858 Commissioning Instructions — 6ES5 998-0CM01, R 08/92, English; ADEGIS archive copy. Section 2.1 discusses the earlier TS 758 arrangement; Section 2.3.1 includes a TK 858 setting note for communication with TS 758H units. This is not the TS 758H operating manual.
+ Siemens Working with S5-DOS/ST — C79000-G8576-C760-03, English. General supporting documentation for the V6.6-era PG/PC environment and interfaces, rather than TS 758H supply or pin-assignment information.