6ES7 193-4CB30-0AA0

Siemens 6ES7193-4CB30-0AA0 ET200S TM-E15C24-01 Spring Terminal Module

Siemens 6ES7193-4CB30-0AA0 is the TM-E15C24-01 spring terminal module for 15 mm wide electronic modules in the ET200S system. It provides eight connection points in a 2 × 4 arrangement. The AUX1 bus continues through the base, with no terminal access to AUX1 on this model. Documentation also writes the order number as 6ES7 193-4CB30-0AA0.

Role alongside the electronic module

The terminal base provides the electronic module's mechanical and electrical connection. Its structure continues the backplane bus connection and the supply buses from the power module. The inserted electronic module determines the functions of terminals 1–8 used for field wiring.

When selecting a base for a PLC station, assess the exact electronic module code, terminal arrangement and required potentials together. The power supply wiring plan is part of that assessment. Compare the base's type marking with the terminal numbers in the project, as well as checking its width.

Eight terminals and the I/O channel count

2 × 4 describes the number of connection points. The electronic module determines the station's I/O channel count and signal type. Terminal count therefore does not establish a measurement range, output current or number of I/O channels.

For example, Siemens lists 6ES7193-4CB30-0AA0 as a usable terminal base in the manual for the 6ES7134-4LB02-0AB0 2AI U HF voltage input module. In this arrangement, the electronic module measures the analog signal, and field wiring follows its connection diagram. Check the relevant compatibility table and terminal functions again when changing to a different electronic module.

AUX1 continuity and terminal access

A continuous AUX1 bus does not provide a connection point on this base. AUX1 passes through the TM-E15C24-01, but terminals 4 and 8 are not connected to AUX1. Their use also depends on the electronic module's wiring diagram.

During replacement, trace the potential distributed through AUX1 in the project documentation. Use the exact base type and terminal markings to determine where a connection can be made. Checking the AUX1 requirement, electronic module signal terminals and panel potential distribution individually helps distinguish bases with similar housings.

Differences from 4CB20 and 4CA30

6ES7193-4CB20-0AA0 is the TM-E15S24-01 version with screw terminals. The 6ES7193-4CB30-0AA0 described here is the TM-E15C24-01 spring terminal version. Because the termination method changes, conductor preparation and installation must follow the instructions for the selected base.

6ES7193-4CA30-0AA0 is the TM-E15C24-A1 type, providing AUX1 access through A4 and A8. Its electronic module connections are terminals 1–3 and 5–7. Terminal functions therefore matter when selecting a base; compare the connections required by the electronic module before substituting one type for another.

Dimensions and packaging quantity

Siemens specifies dimensions of 15 × 132 × 43 mm, width × height × depth, and an approximate weight of 65 g per terminal module. The standard manufacturer packing unit for this order number contains five terminal modules. State clearly whether the requested quantity refers to individual pieces or complete packs when obtaining a quotation.

When replacing a base in an existing station, inspect the spring connections, side contacts, housing and electronic module seating area. If there are burn marks, loose contacts or a broken latch, investigate the connection conditions that caused the problem before fitting the replacement.

Editor's note

Check the TM-E15C24-01 designation, spring termination and absence of terminal access to AUX1 together. Providing the electronic module's order number and a photograph of the existing base helps identify the correct part. Use the Siemens ET200 manuals for terminal diagrams and module compatibility. Availability, item condition and the actual quantity supplied should be confirmed with the quotation.

Related topics

For control and monitoring, explore PLC and HMI systems, operator panels and SCADA. For system research, see Siemens S7-300, about Siemens ET 200 and ET 200 PROFIBUS and PROFINET.

Other module groups: ET 200 analog input modules · Digital input modules · Digital output modules · Connection modules · Additional modules.

Navigation: Siemens ET 200 · Siemens SIMATIC S7 · Siemens S7 PLC · OtomasyonAVM home