6ES7 158-0AD00-0XA0

6ES7 158-0AD00-0XA0 – Siemens SIMATIC DP/DP Coupler

Series: Siemens SIMATIC DP
Category: Data coupler between two PROFIBUS-DP networks

Description and system role

6ES7 158-0AD00-0XA0 is a Siemens DP/DP coupler for exchanging data between two separate PROFIBUS-DP networks. It operates as a DP slave connected to the master on each network. Output data from one PLC side is transferred to the input area on the other, with the same principle applying in reverse.

For example, two independently controlled machines can exchange ready signals, production counts or process status. Before configuring the link, identify both controllers, the data to exchange and the required PROFIBUS/PROFINET network structure.

Data capacity and connections

The coupler transfers up to 244 bytes in each direction. Input and output lengths are defined in the project. The two network connections use two 9-pin female Sub-D sockets, with a maximum supported transmission rate of 12 Mbit/s.

The supply is 24 V DC, with a maximum current consumption of 250 mA. Include other cabinet loads when selecting the power supply. The Siemens data sheet specifies IP20, an operating temperature of 0–55 °C and dimensions of 40 × 110 × 70 mm, width × height × depth. Mount the unit vertically with the DIP switches at the top.

Address settings and data mapping

Each network side has its own PROFIBUS address setting. Addresses are set using the DIP switch banks on top; the GSD and the master's configuration tool define the data lengths. The address on the unit must match the address configured on the corresponding network.

For example, if machine A sends 8 bytes of status information, configure the corresponding input area on machine B to receive that transfer. Both projects must agree on data order, length and bit assignments. Before replacing a unit, save both PLC projects and record the coupler addresses and existing I/O mapping.

Replacement with 0AD01 and the PN/PN distinction

The Siemens manual dated 02/2006 states that 6ES7 158-0AD01-0XA0 can replace the earlier 0AD00. It also explains that SYNC/FREEZE diagnostic information was improved and aligned with the PROFIBUS standard. During replacement, check the existing hardware configuration and how the PLC program interprets diagnostic data.

The 6ES7 158-3AD00-0XA0 PN/PN coupler connects two PROFINET IO networks. Compare the complete 0AD00 and 3AD00 order numbers when selecting a unit; the network protocol and connector type determine which product is suitable.

Troubleshooting and used-unit inspection

When investigating communication faults, check the addresses, cable connections, bus termination and I/O mapping on both networks. Record which master reports the fault. Include communication loss and recovery in the application test plan.

For a used unit, inspect label readability, Sub-D sockets, retaining screws, DIP switches and the power connection. Ask the seller for a test demonstrating data transfer in both directions between the two networks.

Editor's Note

A statement that the coupler powers up gives limited information about its condition. Request evidence that both PROFIBUS sides communicate and transferred values change in the receiving PLC. Photograph the existing unit's label, DIP settings and connector orientation so that the replacement can be compared before installation.

PDF documentation and manuals

See Siemens ET 200 PDF documentation and user manuals for relevant documents. The 0AD00 product data sheet provides electrical and mechanical specifications, while PROFIBUS Networks, 05/2000 explains the earlier coupler's network role. The DP/DP Coupler, 02/2006 manual covers the 0AD01; its references to the 0AD00 support replacement and compatibility checks.

Related topics

For control and monitoring equipment, explore PLC and HMI, operator panels and SCADA. The Siemens S7-300 and About Siemens ET 200 sections may also help when identifying other components in an existing system.

Other module groups: ET 200 digital input modules · Digital output modules · Analog input modules · Connection modules · Additional modules.

Navigation: Siemens ET 200 · Siemens SIMATIC S7 · Siemens S7 PLC · OtomasyonAVM home