6ES5 475-5AA11

Siemens 6ES5 475-5AA11 SIMATIC S5-150A 4-Channel ±10 V Analog Output Module

The Siemens 6ES5 475-5AA11 is an A-format, four-channel ±10 V analog output module for the SIMATIC S5-150A. It converts digital PLC commands into bipolar voltage signals. The outputs are non-isolated, and the module takes an external 24 V DC supply.

In service, the module sends an analog voltage reference to a drive’s analog input or to another control device. In a PLC-based PID loop, for example, the program scales its control output to suit the receiving device’s bipolar range. During commissioning, check how that device interprets −10 V, 0 V and +10 V.

Which rack does it fit?

The Siemens ST 53 ordering table lists the 475-5AA11 in the S5-150A column. The catalog shows A-format expansion racks in the EG 180-3A, EG 181-3A and EG 182-3A configurations. The 741 housing table lists 741-0AB11 and 741-0AB21 for the 475 and 476 analog output modules.

In a distributed S5-150A installation with an EG 182-3A, the IM 301-5AA13 expansion interface and IM 310-5AA12 link module are part of the rack arrangement. Check the existing housing and terminals when choosing an output card, and verify the interface order numbers when tracing the expansion link.

How does it differ from the 475-3AA11 and 476?

The 6ES5 475-3AA11 also has four ±10 V outputs and uses the compact K format. The A-format 476-5AA11 and compact 476-3AA11 provide 0–20 mA current outputs. Match both the format and the signal type when choosing a spare. The receiving device may use separate terminals for its voltage and current inputs.

Supply, output load and terminals

The catalog specifies an external S5 supply of 24 V DC nominal, with a 20–30 V DC range including ripple. Each voltage output requires a load of at least 3.3 kΩ. The outputs are short-circuit protected. Siemens specifies a settling time of 200 µs to 99% with a 200 m shielded cable.

The Siemens 475-5 wiring diagram shows signal and load-reference terminal pairs 1/2, 5/6, 9/10 and 13/14 for channels 0–3 respectively. Because the outputs are non-isolated, check the load’s 0 V reference, cable shield and grounding arrangement against the same diagram. The catalog specifies a maximum of 0.8 V between the load reference and the equipment chassis.

How is the STEP 5 output value represented?

Siemens specifies 8 bits plus sign for the card’s digital representation, with 256 units corresponding to 10 V. If the installed STEP 5 project uses FB 79 ANAU, Siemens’ block table lists this order number under BT = 0 with a −10000 to +10000 input scale. Verify the channel and module start address in the installed program.

Editor’s note

When buying a spare, check the 5AA11 suffix and the A-format housing label separately. Match the housing code before fitting the card to the rack.

Before removal, record the devices connected to all four channels, the output address and the STEP 5 scaling.

Bring the machine to a safe stop. Isolate the rack and external 24 V DC supply before transferring the terminal connections. If there is switching interference, inspect the shield and 0 V conductor.

If the output is low, first measure it against the card’s load reference. Compare the receiving device’s input impedance with the 3.3 kΩ minimum.

If the output is correct and the process responds in the opposite direction, check how the receiving device interprets voltage polarity and verify the loop feedback.

OtomasyonAVM resources and PDFs

+ SIMATIC S5 analog modules · Siemens SIMATIC S5 PLC overview

+ SIMATIC S5 manuals and PDF archive

Related topics

+ 6ES5 475-3AA11 compact ±10 V · 6ES5 476-3AA11 compact 0–20 mA · 6ES5 182-3AA21 expansion rack

Browse SIMATIC S5

+ SIMATIC S5 analog modules · SIMATIC S5 · Used Siemens automation equipment

Siemens and external references

+ Siemens ST 53, S5-150A ordering table (DE, PDF) · 475-5 technical specifications · 475-5 terminal diagram · 741 housing selection table

+ Siemens Modular PID and Fuzzy Control Manual, FB 79 ANAU (DE, PDF)