6ES5 470-7LC13

Siemens 6ES5 470-7LC13 SIMATIC S5 8-Channel 1–5 V / 4–20 mA Analog Output Module

The Siemens 6ES5 470-7LC13 is an eight-channel analog output module in the SIMATIC S5 family, documented for the S5-115U/F. Its nominal output ranges are +1 to +5 V and +4 to +20 mA. The output group is galvanically isolated, with MANA as a common reference for all channels.

The module turns a digital PLC command into a signal for the analog input of a drive, valve positioner or other receiving device. A PLC-based PID loop, for example, can send its control output over +4 to +20 mA. Since voltage and current inputs may use different terminals and scaling, verify that the receiving device expects a lower limit of 1 V or 4 mA.

What changes between S5-115U, F and H installations?

The Siemens data sheet for this order number lists S5-115U/F. The ST 50 ordering table also lists S5-115H. The S5-115H system manual specifies additional hardware circuitry for redundant operation of a 470 analog output. For an H system, check the installed circuit diagram and the card revision together.

For S5-115F systems, such as an installation with a CPU 942F, the F manual shows the 470-7LC family in a nonsafety-related analog output application. Check the module location and address against the installed S5 rack layout. In an S5-115U installation with a CR 700-2, for example, the physical slot must match the STEP 5 peripheral address.

How do the 7LC13, 7LA13 and 7LB13 differ?

The 6ES5 470-7LA13 provides ±10 V / 0–20 mA, while the 6ES5 470-7LB13 provides ±10 V. The 470-7LC11 and 470-7LC12 are earlier order numbers documented with the same nominal 1–5 V / 4–20 mA ranges. When selecting a spare, compare the full 7LC13 suffix, the rack arrangement and the front connector.

Front connector, supply and load limits

Siemens specifies a 46-pin 490 front connector. The S5 connector range includes the 490-7LB21 screw-terminal, 490-7LA11 crimp with contacts and 490-7LA21 crimp without contacts versions. The 7LC13 diagram marks QV for voltage output, QI for current output, S+/S− for the sense lines and MANA for the common analog reference.

For an unused voltage output, the S5-115U diagram for the 470-7LCxx shows QV to S+ and S− to MANA jumpers on the same channel. An unused current output remains open. When changing to current wiring, check the existing jumpers and the shielding and grounding arrangement against the diagram.

Siemens’ 470-7L.13 technical table gives an external S5 supply of 24 V DC nominal, 20–30 V DC. The resistive load limit is 3.3 kΩ minimum for voltage output and 300 Ω maximum for current output. The table specifies a 1 ms conversion time and 12-bit two’s-complement representation, with 1,024 units corresponding to the rated value. In the S5-115U manual, the CPU uses two bytes per channel.

Editor’s note

Read the 7LC13 suffix on the spare. The LA and LB cards use a similar housing and have different output ranges.

Before removal, record the slot number, channel addresses and program scaling. On an H or F installation, cross-check the approved wiring arrangement.

Bring the machine to a safe stop and isolate the rack and the external 24 V DC supply. Photograph the front-connector jumpers before removing them.

If the output fails to reach 20 mA, compare the total load of the receiving device and any series components with the 300 Ω limit. On a voltage channel, check the input impedance and the sense connections.

If all channels are affected, check the L+/L− supply and the MANA reference separately. For a fault on one channel, start with its QV or QI connection.

OtomasyonAVM resources and PDFs

+ SIMATIC S5 analog modules · Siemens SIMATIC S5 PLC overview

+ SIMATIC S5 manuals and PDF archive · S5-115H System Manual, redundant operation of 470 outputs (PDF)

Related topics

+ 6ES5 470-7LC12 1–5 V / 4–20 mA · 6ES5 470-7LA13 ±10 V / 0–20 mA · 6ES5 470-7LB13 ±10 V · 490-7LB21 screw-terminal front connector

Browse SIMATIC S5

+ SIMATIC S5 analog modules · SIMATIC S5 · Used Siemens automation equipment

Siemens and external references

+ Siemens 6ES5 470-7LC13 data sheet (DE, PDF)

+ Siemens ST 50, 470-7L.13 technical specifications (PDF) · 7LC13 ordering table and front connector diagram

+ SIMATIC S5-115U System Manual, 470-7LCxx load connections (PDF)

+ SIMATIC S5-115F System Manual, Type 18 analog output application (PDF)