
Crane capacity: will the rating cover the whole lift?
A crane's advertised tonnage is a starting point. The useful figure is the permitted load in the actual configuration, at every position along the planned route. A machine may handle a heavy load close to its centre of rotation and a much smaller load farther away. Check the pick, the travel path and the landing position before choosing the crane.
A maximum rating comes with conditions
For a boom crane, capacity depends on working radius, boom configuration, counterweight, support arrangement and operating sector. Working radius is the horizontal distance from the crane's axis of rotation to the vertical line through the load. It is not the boom length. Use the manufacturer's load chart that matches the machine as configured.
Two published examples illustrate the difference. Liebherr lists the LTM 1120-4.1 with a maximum capacity of 120 t at a 3 m radius. Potain's MDT 219 J10 product page lists a 10 t maximum capacity, a 65 m maximum radius and approximately 1.9 t tip capacity. These figures describe different lifting conditions; they are not interchangeable ratings or approval for a particular site lift.
Check the units before comparing specifications. Here, one metric tonne (t) equals 1,000 kg. A US short ton, often shown as USt, is a different unit. A loader crane's tonne-metre (t·m) rating describes lifting moment, rather than a load it can lift at any reach.
Different cranes require different capacity checks
Broad tonnage ranges for crane types can hide the information needed for selection. The table below identifies the main checks. “Telescopic” describes a boom arrangement that can be used on mobile and rough-terrain cranes; these labels are not mutually exclusive categories.
| Crane type | What to check |
|---|---|
| Tower crane | Jib reach, trolley position, installed equipment and capacity at the tip. |
| Mobile / telescopic crane | Radius, boom configuration, counterweight, outrigger setup and slewing sector. |
| Crawler crane | Boom arrangement, track stance, ground conditions and any separate travel-with-load requirements. |
| Rough-terrain crane | The applicable on-outrigger or on-tyre chart; one does not replace the other. |
| Overhead crane | The relevant hoist rating, permitted combinations of loads and supporting structure. |
| Gantry crane | The hoist, bridge, legs and runway or ground arrangement as a complete installation. |
| Floating crane | Crane configuration together with platform stability, list and marine conditions. |
| Truck-mounted loader crane | The reach/load diagram, vehicle installation, stabilisers and permitted operating area. |
Account for everything the chart requires
The component being moved is only part of the assessment. Include slings, lifting beams and other load-handling attachments. Read the chart notes to establish how hook blocks, rope and installed equipment are accounted for. Do not omit a required deduction or subtract an allowance that has already been included. Each item of rigging equipment also needs an appropriate working load limit for its actual use.
Illustrative example: assume a hypothetical chart permits a 5,000 kg gross load at the selected position. Its notes require deductions for a 250 kg hook block, 100 kg of slings and a 350 kg lifting beam. The remaining allowance for the component is 5,000 − 250 − 100 − 350 = 4,300 kg. This explains chart deductions; it does not establish the capacity of a real crane.
Obtain dependable weight information from the manufacturer, an appropriate calculation or a suitable measurement. When using a crane scale or load cell, check its range, sensor type and verification. Understanding how load cells work helps explain the reading, but a displayed weight is not proof that an overload safety function has been validated.
Follow the load through its full route
Match the machine, the chart and the installed configuration first. Then assess the pick, intermediate positions and landing point. A load that is within capacity at the start may exceed the rating at a larger radius. Rope reeving and permitted line pull can impose additional limits. Do not invent a capacity for a configuration or position outside the chart.
Crane selection must also address ground support, centre of gravity, sling angles, exposed wind area and the effects of movement. A capacity limiter, limit switch or PLC does not make an incorrect setup acceptable. Safe lifting practices and a competent crane operator remain essential to the decision.
Drive power and lifting capacity are different specifications
Fitting a larger motor or drive does not automatically increase the crane's approved rating. A suitable crane drive, vector control and encoder feedback help control motion. Managing regenerated energy and sizing a braking resistor matter during lowering, but do not increase structural capacity. Hoist drive selection must account for the motor and mechanical brake arrangement.
Rated load and duty class answer different questions. Two cranes with the same capacity can be designed for different operating frequencies and load histories. Specify daily cycles, typical loads and shifts when deciding whether to buy or rent. Review maintenance records and relevant standards when assessing suitability for the intended service.