Faq For Profibus?

PROFIBUS is a digital fieldbus technology developed for reliable data exchange between controllers and field devices in industrial communication systems. It has been widely used to connect PLCs, remote I/O stations, motor drives, sensors, valve islands and process instruments without requiring separate point-to-point control wiring for every signal.
In simple terms: PROFIBUS allows one industrial controller to communicate with many devices over a common fieldbus. Instead of running a separate control cable for every measurement and command, devices exchange operating data, status information and diagnostic messages digitally over the network.
What does PROFIBUS mean?
The name PROFIBUS originated from Process Field Bus. However, this should not be confused with the meaning of PROFIBUS PA. In PROFIBUS PA, the letters PA stand for Process Automation. PROFIBUS is therefore a family of fieldbus technologies rather than a single cable type or one fixed application.
Within an industrial automation system, PROFIBUS can provide the communication path between the central controller and equipment distributed around a machine or process plant. The two best-known forms are PROFIBUS DP and PROFIBUS PA.
What is PROFIBUS DP?
PROFIBUS DP is designed primarily for fast communication with decentralized peripherals. The abbreviation DP refers to Decentralized Peripherals. A PLC can use PROFIBUS DP to exchange cyclic I/O data with remote input/output stations, drives, weighing systems, valve terminals and other automation equipment.
The most common copper physical layer for PROFIBUS DP is based on RS-485 differential signalling. Supported PROFIBUS DP data rates extend from 9.6 kbit/s to 12 Mbit/s. As with many serial bus systems, the practical cable length available on one segment decreases as the communication speed increases.
For Type A PROFIBUS cable, commonly referenced segment lengths are approximately 1200 m at 9.6 to 93.75 kbit/s, 1000 m at 187.5 kbit/s, 400 m at 500 kbit/s, 200 m at 1.5 Mbit/s and 100 m at 3 to 12 Mbit/s. These figures assume a correctly designed segment with suitable cable and termination; they are not universal guarantees for arbitrary wiring.
What is PROFIBUS PA?
PROFIBUS PA was developed for process automation and is particularly suitable for field instruments such as pressure, temperature, level and flow transmitters, analysers and valve positioners. These devices are often part of wider monitoring systems in which field information eventually reaches a SCADA system or distributed control architecture.
A common PROFIBUS PA physical layer is MBP — Manchester Coded Bus Powered. It operates at a fixed data rate of 31.25 kbit/s and can carry both communication data and power for suitable field devices over the same two conductors. This is an important difference from the conventional RS-485 implementation normally associated with PROFIBUS DP.
PROFIBUS PA can also be engineered for hazardous process areas when appropriate approved field devices, barriers, power supplies and installation methods are used. PROFIBUS PA itself should not be treated as an automatic hazardous-area approval; the complete installation still has to satisfy the applicable protection concept and equipment requirements.
What is the difference between PROFIBUS DP and PROFIBUS PA?
PROFIBUS DP is generally associated with machine automation, remote I/O and fast communication with devices such as variable frequency drives. PROFIBUS PA is aimed at process instruments where field-device power, long process segments and hazardous-area considerations may be important.
DP and PA can be part of the same automation architecture. A DP/PA coupler or link can connect a high-speed PROFIBUS DP network to one or more PROFIBUS PA field segments. Such a device is more than a mechanical connector: it interfaces two different physical transmission systems and, depending on its design, also provides the required power and communication conversion for the PA segment.
How does PROFIBUS communication work?
In traditional PROFIBUS terminology, stations capable of initiating communication are called masters, while field devices responding to a master are called slaves. These terms remain common in existing documentation and installed systems even though newer industrial documentation increasingly uses controller/device terminology.
In a typical machine with one master, the PLC controller cyclically exchanges input and output data with configured field devices. Where several active masters share the same network, bus access between those active stations is coordinated through a token-passing mechanism. Communication between a master and its assigned field devices follows the master-device communication principle.
This makes PROFIBUS suitable for transferring process inputs, control outputs, drive control words and equipment status information in predictable cycles. A PROFIBUS-connected HMI may display values originating from the PLC network, while supervisory information may also be passed onward to SCADA for plant-level monitoring and alarms.
What are DP-V0, DP-V1 and DP-V2?
DP-V0 provides the fundamental PROFIBUS DP functions used for cyclic I/O exchange and basic diagnostics. DP-V1 extends the system with acyclic communication, alarms and additional parameter access. DP-V2 introduces further functions for demanding automation applications, including features related to synchronization and time-dependent data exchange.
The fact that a device carries a PROFIBUS DP interface does not mean that it supports every DP-V0, DP-V1 or DP-V2 service. The actual capabilities must be checked in the device documentation and configuration data, particularly when older drives or remote I/O systems are being connected to a newer PLC platform.
What is a PROFIBUS GSD file?
A GSD file describes important communication characteristics of a PROFIBUS device so that engineering software can recognise and configure it. Depending on the device, this may include supported baud rates, module structures, input/output data lengths and diagnostic capabilities.
When a new remote I/O station or VFD is added to a PLC project, the correct GSD file may be required before the engineering software can configure the unit properly. Importing the file alone is not enough: the device address, selected modules and I/O mapping must also correspond to the actual hardware.
Physical connection should also be distinguished from device configuration. A suitable PLC communication cable or PROFIBUS connector can provide the electrical connection, but it cannot correct an incorrect GSD, wrong station address or mismatched PLC hardware configuration.
How should a PROFIBUS DP network be wired?
The preferred topology for an RS-485 PROFIBUS DP segment is a linear bus. The network cable passes from one station to the next, with termination at the two physical ends of the segment. Long uncontrolled stubs and star-shaped passive branches should be avoided, especially at higher data rates.
Proper PROFIBUS Type A cable should be used rather than treating any available twisted pair as equivalent. Cable routing is equally important. PROFIBUS communication cable should not be run for long distances directly alongside motor leads, contactor power wiring or PWM output cables from motor drives.
Shielding and equipotential bonding must also be considered. Differential signalling provides good noise immunity, but it does not make the network immune to poor EMC installation practices, damaged shields or large potential differences between panels.
How is PROFIBUS termination connected?
An RS-485 PROFIBUS DP segment requires termination at its two physical ends. PROFIBUS termination should not be simplified to a single ordinary resistor placed across the two signal conductors. The conventional PROFIBUS RS-485 termination network uses a 390 Ω – 220 Ω – 390 Ω resistor arrangement connected to the appropriate reference supply.
Many PROFIBUS D-sub connectors include a switch that enables or disables the termination network. The first and last stations normally have termination enabled, while intermediate stations have it disabled. Accidentally leaving termination enabled on a middle device is a common cause of unstable or completely failed bus communication.
Another practical issue is that standard PROFIBUS termination is powered. If the equipment located at the end of the segment is switched off and its connector no longer supplies the termination network, communication on the remaining bus can become unstable. An independent active terminator may be useful where an end station must frequently be powered down.
How many devices can be connected to PROFIBUS?
For a conventional RS-485 PROFIBUS DP segment, 32 nodes per electrical segment is an important design limit, including active and passive bus stations. Larger installations can be divided into additional segments using repeaters. The total network design must also respect device addressing and controller-specific limits.
The practical number of PROFIBUS PA field devices may be limited by additional factors such as segment power supply, device current consumption, hazardous-area barriers, cable length and the characteristics of the coupler or power conditioner. A fixed device count should therefore not be applied to every PA installation without an electrical segment calculation.
Are PROFIBUS and PROFINET the same technology?
No. PROFIBUS is a traditional industrial fieldbus system, while PROFINET is based on industrial Ethernet technology. Both belong to the wider industrial automation communication landscape, but they use different physical infrastructures and communication mechanisms.
PROFINET can take advantage of switched Ethernet networks, higher bandwidth and Ethernet-based diagnostics. PROFIBUS DP normally uses its dedicated RS-485 bus infrastructure. The existence of a newer Ethernet-based system does not automatically make every operating PROFIBUS installation obsolete.
This distinction is similar to the broader difference between traditional fieldbus systems and modern EtherCAT or EtherNet/IP networks. All are used in industrial control, but their frame handling, topology, device models and real-time mechanisms are different.
Can PROFIBUS and PROFINET be used in the same plant?
Yes. Existing PROFIBUS equipment does not necessarily have to be removed when a plant introduces Ethernet-based automation. Gateways, proxies and controllers supporting both network families can allow legacy PROFIBUS segments to remain operational while higher-level communication moves toward Ethernet.
This type of mixed architecture is common during modernization because existing drives, remote I/O and field instruments may still be serviceable. Replacing every field device merely to change the communication network can create more cost and production downtime than the network upgrade itself.
Where is PROFIBUS used?
PROFIBUS DP has been widely installed in manufacturing machinery, conveyors, packaging lines, motor control systems, distributed I/O and general factory automation. A PROFIBUS-capable variable frequency drive can receive speed references and control words from a PLC while returning status words, actual values and fault information over the same network.
This is not merely theoretical support. Industrial drives such as the ABB ACS550 have been offered with PROFIBUS fieldbus connectivity, while communication options for other drive families can include PROFIBUS DP alongside PROFINET, EtherNet/IP and other industrial networks.
PROFIBUS PA is more closely associated with process industries such as chemical plants, water treatment, energy systems and other facilities using large numbers of process instruments. Measurements collected from those field devices can be processed by the control system and presented through an HMI panel or a plant-level SCADA system.
Why does a PROFIBUS network fail?
Many PROFIBUS faults originate at the physical layer rather than in the PLC program. Common causes include missing or excessive termination, reversed or broken signal conductors, loose connectors, inappropriate cable, long stubs, damaged shielding, electromagnetic interference and a communication speed that is unsuitable for the installed segment length.
Once the physical network has been verified, check the PLC configuration, station addresses, GSD files, module sequence and I/O lengths. A field device may be electrically visible on the bus but still remain in a configuration fault state when the PLC project does not match the real hardware.
Troubleshooting should therefore use more than a simple “device online/offline” indication on the HMI. Controller diagnostics, field-device LEDs, connector condition, network statistics and, when necessary, a PROFIBUS analyser should be evaluated together.
Practical PROFIBUS troubleshooting sequence
1. Check whether the controller and field devices support the intended PROFIBUS mode and data rate.
2. Confirm that every station address is correct and that duplicate addresses are not present.
3. Verify that termination is enabled only at the two physical ends of the segment.
4. Check whether an end device being powered down also removes power from the termination network.
5. Inspect the PROFIBUS cable, connectors, shield connections and A/B conductors.
6. Compare the actual segment length with the selected communication speed.
7. Verify the GSD file, hardware modules and I/O mapping in the PLC project.
8. If the problem remains intermittent, analyse the physical bus signal and diagnostics instead of repeatedly changing software parameters.
Is PROFIBUS still used today?
Yes. PROFIBUS has a very large installed base in industrial plants. Whether an existing network should remain in service or be modernized depends less on its age alone and more on spare-parts availability, equipment support, production requirements, maintenance capability and the long-term automation strategy.
For a new installation, an Ethernet-based industrial network may offer advantages in bandwidth and system integration. For an existing production line, however, a properly operating PROFIBUS system can remain perfectly useful. Migration should be an engineering and economic decision rather than a decision based simply on which protocol is newer.
Related Industrial Communication Guides
Industrial Communication · Ethernet FAQ · What Is Ethernet? · EtherCAT · EtherNet/IP in Industrial Automation
Related Automation Pages
PLCs and Modules · HMI Panels · SCADA · AC Drives · PLC Communication Cables