• Gemo DT107P

Gemo DT107P-230VAC-R Heat Controller

Gemo control products have been sold by our company since 2013.

Gemo DT107P is a 72x72 mm digital temperature controller designed for industrial heating and process control applications.

Mounting dimensions: 72x72 mm
Supply: 220VAC standard version
Outputs: 2 relay outputs – SSR output must be specified when ordering.

Heating Hysteresis: 0 .. 50 / 0.0 .. 50.0 °C (H.Hys). When the H.Hys value is set to 0, PID control becomes active for the heating function.

The controller supports relative, absolute, band and sensor-failure alarm functions.

Line Compensation: Maximum 10 Ohm with 3-wire Pt100.

Derivative Time: 0:00 .. 10:00 min:sec. When set to 0:00, derivative control is disabled.

Cooling Output: Cooling output delay function is available.

Sensor Protection: If the sensor or sensor line is broken, the measurement is outside the measuring scale, or the input measurement fails, the OUT output operates according to the P.Err and Ct parameters. If P.Err is 0, the output remains OFF. The alarm output should also be considered for this condition.

Alarm Hysteresis: 1 .. 50 / 0.1 .. 50.0 °C (A.Hys)

The unit provides password protection and keeps program and control parameters in memory.

Control modes: P, PI, PD, PID or ON-OFF control.

Input: J type optional. You can view all temperature sensor models available on our website.

Sensitivity: ±1 °C or ±0.1 °C

Alarm Output: Relay, NO + NC, 250VAC, 2A resistive load. DT104 version has NO output only.

Integral Time: 0:00 .. 30:00 min:sec. When set to 0:00, integral control is disabled.

Power Consumption: < 8VA

Heat SET Setting: Lo.L .. UP.L °C (H.Set)

Supply Voltage: 100..240VAC, 50-60Hz or 24VDC/AC; insulation voltage maximum 40VAC.

Measurement Scale

-100 .. 600 °C with J type thermocouple input (Inpt = J type thermocouple).

Note: Suitable temperature measuring sensors can be found in our Pt100 and thermocouple section.

Technical Note: You can also read our short Pt100 and thermocouple comparison.

Alarm SET Setting: AL.tY = Abs, -Abs; Lo.L .. UP.L °C (A.Set)

Control Period: 1 .. 200 sec (Ct)

Display: 4-digit 7-segment PV display and 4-digit 7-segment SV display

Sensor Types: T/C (J, K, T, S, R), Pt100 and optional multi-input configurations.

PID Control Parameters

PbC – Proportional Band: Indicates how many degrees before the H.SET value the time-proportional control operation starts.

Ct – Control Period: A value between 1 and 10 seconds should generally be selected for good control performance.

Ti – Integral Time: The difference between the process value and SET value is compensated by the PID algorithm. A lower Ti value provides a faster response; however, excessively low Ti values should be avoided because they may cause process oscillation. If Ti is set to 0, the integral section of the algorithm is ignored and the controller operates as P or PD.

Td – Derivative Time: Sudden changes between the process value and SET value are compensated by the PID algorithm. Increasing Td increases sensitivity to sudden changes; therefore, excessively high Td values should be avoided. If Td is set to 0, the derivative section is ignored and the controller operates as P or PI.

Documentation: Gemo DT107P User Manual (PDF)

Gemo Price List

Gemo Contact

Gemo Electronic Main Page

Control Devices Main Page


Attention: Installation and assembly of Gemo electronic controllers must only be performed by qualified technical personnel. Installation must comply with applicable regulations, including relevant requirements of 2006/42/EC.

Otomasyon AVM accepts no responsibility for installations performed in violation of local laws or applicable regulations. Failure to follow GEMO installation and operating instructions may also affect warranty coverage.

For detailed information, please use the Gemo contact page or contact gemo@otomasyonavm.com.

Write a review

Note: HTML is not translated!
Bad Good

Gemo DT107P

  • 51.00USD

  • Ex Tax: 51.00USD

Related Products

DESA-77R-A Analog Temperature Controller, 220V

DESA-77R-A Analog Temperature Controller, 220V

▪︎ DERELL DESA-77R-A >> 220V Power Supply, Relay Output, 72x72 mm Panel Type Temperature Contr..

128.00USD Ex Tax: 128.00USD

DGS-77R-A Advanced Temperature Controller (220V)

DGS-77R-A Advanced Temperature Controller (220V)

— Next-generation temperature compensation with high precision DGS-77R-A >> 220V pow..

131.00USD Ex Tax: 131.00USD

DGS-77T-A – Advanced Serial Type with SSR Output – 220V

DGS-77T-A – Advanced Serial Type with SSR Output – 220V

— Next-generation temperature compensation with high precision DGS-77T-A >> 220V pow..

136.00USD Ex Tax: 136.00USD

DGS-77R-B Advanced Temperature Controller (24VAC/DC)

DGS-77R-B Advanced Temperature Controller (24VAC/DC)

— Next-generation temperature compensation with high precision DGS-77R-B >> 24VDC/AC..

205.00USD Ex Tax: 205.00USD