Delta ECMR

Delta ECMR Robot Servo Motors

The Delta ECMR is an AC servo motor family designed for robot axes. The ECMR-CV models in Delta’s ASDA-MS catalogue are rated at 220 V and 3,000 rpm. In industrial applications such as pick-and-place, assembly and transfer, the motor works with the robot controller and mechanical transmission. In robotics, the gear ratio and axis reference translate motor shaft position into control of the arm position.

ECMR-CV motor codes and dimensions

ECMR-CV0401RS · 100 W, 40 mm frame, 8 mm shaft diameter.

ECMR-CV0602RS · 200 W, 60 mm frame, 14 mm shaft diameter.

ECMR-CV0604RS · 400 W, 60 mm frame, 14 mm shaft diameter.

In ECMR-CV0602RS, C denotes the 220 V, 3,000 rpm class, V the magnetic absolute encoder, 06 the 60 mm frame and 02 the 200 W rating. Delta specifies 22-bit single-turn resolution and 16-bit turn counting for the V-type encoder. The feedback value describes the motor shaft. The robot’s mechanical zero, backlash and coupling alignment also affect tool-point positioning accuracy.

ASDA-MS and SCARA motor combinations

Delta lists the three RS codes above under ASD-MS-0421-F-□ in the ASDA-MS catalogue. When replacing a motor or servo drive, verify the motor and drive combination by full model code and axis. Compare the power, brake and encoder connections with the device drawings and the Delta servo cable tables.

The SCARA CE service manual lists ECMR-CV0604RS for M1, ECMR-CV0602RX for M2 and ECMR-CV0401PX for M3 and M4 in the parts list for the DCS-1B00-CA system. Order by the full robot model, axis number and suffix on the removed motor. For mechanically modified axes, check motor sizing against load inertia, cycle time, and the required speed and torque.

Checks after motor replacement

Back up the axis settings first. After verifying the mechanical reference, check axis direction, single-axis travel and coordinated axis motion. Confirm the robot path in the operating program. Where a robot works with a PLC, test cycle permission and axis-ready signals as well.

Editor’s Note

Ask for photos of the nameplate, shaft and sockets when buying used. The 200 W ECMR-CV0602RS and ECMR-CV0602RX share the same power code. Use the full label, axis parts list, shaft dimensions and connector details to select the spare.

Record the robot’s zero position before removal. Record the axis number, current position value and mechanical reference marks. Complete the robot’s reference verification after replacing the motor. Even if jog motion looks normal, measure whether the tool repeatedly returns to a known point.

Look up the battery warning in the robot manual. On the SCARA CE systems covered by this manual, Ed061 is a battery voltage warning. Follow the procedure for the exact robot and enter the warning and position check result in the maintenance record.

Inspect the cable if the alarm always appears at the same arm angle. Check where the encoder lead flexes at the joint and make sure the connector latch is intact. Include the power and signal routes in the shielding and electrical noise checks.

Check the mechanical transmission if the axis jerks on stopping. Inspect the coupling, gearbox backlash and tool load. If you use the controller’s supported auto-tuning function, measure the axis response again under actual load. If heating accompanies the symptoms, log motor temperature alongside cycle time.

Delta ECMR PDF downloads

ASDA-MS Catalogue and ECMR Motor Tables · English, 13 April 2021, 36 pages. ECMR ordering codes on PDF page 16 and drive and motor combinations on PDF page 19.

Delta SCARA CE Robot System User Manual · English, 13 August 2019, 203 pages. Battery maintenance and motor parts lists for the DRS40L, DRS50L, DRS60L, DRS70L and DRS60H CE systems.

For other documents, visit the Delta Servo Manuals archive.

Related topics and Delta equipment

Servo system FAQs · Delta servo motor families

For other motor families, see Delta ECMA, Delta ECMC, Delta ECML linear motors and Delta ECMS spindle motors.

Manufacturer reference · Delta Electronics ASDA-MS robot controllers