Delta ASDA-B2-F
Delta ASDA-B2-F DMCNET Servo Drive Series
The Delta ASDA-B2-F is a single-axis AC servo drive that receives position commands from a compatible motion controller over DMCNET. Each B2-F runs one servo motor. In machine applications such as feeding, indexing and transfer, several drives can share a controller. Axis synchronisation depends on the controller and network configuration.
Model codes and supply
100–750 W: ASD-B2-0121-F (100 W), ASD-B2-0221-F (200 W), ASD-B2-0421-F (400 W), ASD-B2-0721-F (750 W).
1–3 kW: ASD-B2-1021-F (1 kW), ASD-B2-1521-F (1.5 kW), ASD-B2-2023-F (2 kW), ASD-B2-3023-F (3 kW).
The series has a nominal supply of 200–230 V AC, 50/60 Hz. The B2-F wiring guide shows single- or three-phase supply for the 100 W–1.5 kW models and three-phase supply for the 2–3 kW models. Use the phase and input current on the drive nameplate when selecting panel and protection components.
DMCNET wiring, operating modes and ASDA-Soft
CN6 carries the DMCNET input and output connections. Delta specifies shielded RJ45 cabling, a 120 Ω terminator at the last drive and station numbering through P3-00. When fitting a spare, compare its station number with the axis list in the PLC or motion controller. Related Delta units include the AH20MC-5A motion module and the HMC07 controller family. Confirm compatibility using the exact master model and firmware version.
In P1-01, 0B selects DMCNET position control. 04 (Sz) and 05 (Tz) are the internal speed and torque command modes selected through digital inputs. A compatible version of ASDA-Soft can read and back up parameters through CN3 RS-232. Save the original file before changing drive settings.
ECMA motor, encoder and cable selection
Delta’s motor and drive matching table lists ECMA-C△0604□S for the ASD-B2-0421-F and ECMA-C△0807□S for the ASD-B2-0721-F. Use the full Delta ECMA code to confirm the encoder, brake and shaft options. CN2 carries motor feedback. Select the power and encoder leads by the complete motor code in the Delta servo cable tables.
When sizing a motor for a new axis, account for load inertia, speed, peak torque and cycle time. After fitting a spare, command a known distance and measure the actual travel. The electronic gear ratio and mechanical backlash both affect positioning accuracy.
Editor’s Note
Look for the F suffix and CN6 before buying. If you need an ASD-B2-0421-F, ask the seller for a photo of the front panel and complete nameplate. Compare the rating, connector and model code with the installed unit.
Make sure the controller can see the axis on a used drive. A panel JOG test confirms that the motor can turn. On DMCNET, also check that the drive appears at the right station, follows a position command and returns feedback to the controller.
Back up the station, I/O and travel settings before removal. Record the P3-00 station number, P1-01 operating mode, electronic gear ratio and digital I/O assignments. Compare the replacement settings with the machine records before its first measured move.
Record when the alarm occurs. For AL301, check DMCNET synchronisation, the controller’s SYNC status and line termination. If the alarm only occurs at one cable carrier position, inspect the leads and connectors at that point alongside the shielding and electrical noise checks.
Start with the mechanics if the axis vibrates under load. Inspect the coupling, guides and transmission backlash. After auto-tuning, observe the axis response under the actual load. Add the speed, direction and load at which the vibration occurs to the servo maintenance record.
For AL002 on deceleration, record the cycle conditions. Review the load, stop ramp and regenerative braking circuit together. If the fault returns after the machine warms up, log the motor temperature and cabinet airflow along with the operating cycle.
Delta ASDA-B2-F PDF downloads
ASDA-B2-F DMCNET User Manual · English, September 2015, 291 pages. CN6 wiring, operating modes, parameters and alarm codes.
ASDA-B2 Technical Catalogue · English, January 2014, 36 pages. B and F ordering codes, motor options and dimensions.
For documents on other series, visit the Delta Servo Manuals archive.
Related topics and Delta equipment
Servo system FAQs · Delta servo communication units · Delta servo drive series
For documentation on other drives, see standard Delta ASDA-B2, Delta ASDA-B2L, Delta ASDA-A2 and Delta ASDA-B3.
Manufacturer reference · Delta Electronics ASDA-B2-F user manual