Delta DVP32SN11TN

Delta DVP32SN11TN – 32-Channel NPN Digital Output Module

The Delta DVP32SN11TN adds 32 NPN transistor outputs to a compatible Delta DVP Slim PLC. It connects to the CPU’s right-side expansion bus and provides field wiring through a 40-pin MIL/IDC connector. Typical applications include panels with multiple status lamps, interposing relays or compatible DC control inputs.

Output voltage, channel current and temperature

Delta’s 2026 model table specifies 5–30 V DC and a maximum of 0.1 A per output. The common-current limit is 2.2 A/COM at 25 °C and 1 A/COM at 55 °C. Output response is less than 0.1 ms from OFF to ON and less than 0.3 ms from ON to OFF. PLC scan time and the connected load also affect the response in service. For an older module, confirm the voltage limit against its hardware documentation.

How the NPN output switches the load

A PLC output module transfers the program’s Y command to a field circuit. When this model’s sinking output turns on, current flows from +24 V through the load and Y output to ZP/0 V. Connect one side of the load to +24 V and the other to the appropriate Y output. When connecting a drive or another PLC input, use the receiving device’s diagram to check its common terminal and NPN/PNP wiring.

Add the current of the loads that share a common return and operate at the same time. Sixteen loads drawing 80 mA each total 1.28 A, which exceeds the stated 1 A limit at 55 °C. When using an interposing relay, check the coil current and use a suitable flyback diode. Routing the output cable away from motor wiring helps reduce electromagnetic interference. Select the load circuit fuse and panel grounding for the installation.

40-pin connector, UP/ZP and terminal board

The connector shows two 16-point banks labeled Y0–Y17 and Y20–Y37. Connect the positive side of the external 24 V DC supply to UP and the 0 V return to ZP. Delta’s numbered diagram shows pins 17–18 and 37–38 as ZP/GND and pins 19–20 and 39–40 as UP/+24 V. Match the connector’s pin 1 mark to the manufacturer’s diagram before wiring.

The UB-10-OT32A / DVPAETB-OT32A terminal board brings the 32 outputs out to screw terminals. Delta’s cable guide lists the UC-ET010-24A cable for the UB-10-OT32A. The DVPAETB-OT32A instruction sheet specifies the DVPACAB7A10 40-pin to 40-pin cable.

Y addressing, programming software and cable

The Y numbers on the connector are local terminal labels. The CPU and expansion order determine the actual addresses in the PLC program. In Delta’s example, the DVP32SN11TN uses Y20–Y57 as the first output expansion. The addresses use octal numbering. For example, Y30 follows Y27. When replacing a module, compare the field output list with the PLC program.

Download the program to the host CPU using a compatible version of WPLSoft or ISPSoft. Select the ISPSoft connection through COMMGR. The DVP-SS2 COM1 RS-232 port can use a UC-PRG020-12A cable or a UC-MS020-01A cable with a PC serial port. The UC-PRG015-01A is an option for the DVP-SX2 mini-USB port.

Editor’s Note

When buying a used unit, confirm the DVP32SN11TN label. Look for bent pins on the IDC connector and damage to the side expansion socket.

Before removing the old module, photograph the ribbon cable’s pin 1 orientation and the external terminal order.

If a bank of outputs fails, use a multimeter to check its UP/ZP supply at the terminal board. Delta’s instruction sheet identifies LV as the low-voltage indicator.

On the bench, select channels from both banks. Use a suitable 24 V DC test load to confirm which physical output responds to each Y command.

If outputs work individually and fail together, check the total current of the active loads and the panel temperature.

Related models and products

The DVP08SN11T has eight NPN outputs and the DVP16SN11T has sixteen. The DVP16SN11TS has sixteen PNP outputs. The DVP32SM11N provides 32 digital inputs. For a new standalone control design, see the Derell B Series PLCs.

Manual and wiring diagram

The 40-pin output diagram appears in the 2026 edition of the DVP Series Module Manual, section 7.4.9, page 7-13. See Delta DVP PLC files for series documentation.

DVP32SN11TN · DVP Slim digital modules · Used Delta PLC models · Delta Automation