Delta DVP-F2AD
Delta DVP-F2AD — Two-Channel Analog Input Function Card
Delta DVP-F2AD is a two-channel analog input card that fits the function card slot of a supported Delta controller. CH0 and CH1 convert 0–10 V DC or 0–20 mA sensor signals into digital values. The card adds two analog inputs for applications such as pressure sensing, level measurement and position feedback.
Host compatibility and installation
Delta documents the card for DVP-EH, DVP-EH2 and DVP-EH3 systems. Its programming manuals also cover supported DVP-SV and DVP-SV2 hosts, and the DVP catalogue lists DVP-PM motion controllers. Check the full CPU model, function card slot and applicable CPU manual before buying. Switch off the host before fitting the card.
Signal ranges and terminals
The 0–10 V DC voltage input maps to 0–4000 counts. The nominal step is 2.5 mV and the input impedance is 40 kΩ. Use V0+ for CH0 and V1+ for CH1. The programming manual specifies 12-bit digital resolution for voltage and 11-bit for current.
The 0–20 mA current input maps to 0–2000 counts. The nominal step is 10 µA and the input impedance is 250 Ω. Delta’s current-input diagram shows a jumper between V0+ and I0+ for CH0 and between V1+ and I1+ for CH1. Connect the current signal to the joined terminals and its return to COM.
The two channels share the same COM signal return. Delta’s example uses one voltage channel and one current channel. Check polarity, transmitter power and the channel jumper separately when wiring 0–10 V and 4–20 mA signals. The listed ranges are for positive signals.
PLC registers, software and cable
Read the CH0 present value from D1056 and the average from D1110. For CH1, use D1057 and D1111. Delta’s EH card example reads these special D registers directly. For example, MOV D1056 D0 copies the CH0 present value to D0. On CPUs that report the function card type in D1149, 8 identifies the DVP-F2AD. For the PM series, check the special registers in the host manual.
D1118 relates to the update interval. The 2024 DVP-0407730-02 instruction sheet specifies at least 150 ms. An older sheet and the general programming manual also list a 5 ms setting. Match the setting to the card and host documentation, then measure the interval in your application.
Edit the PLC program on the host. Use WPLSoft or ISPSoft as supported by the EH/SV CPU, or PMSoft for DVP-PM. Delta’s cable guide lists UC-PRG020-12A for USB and UC-MS020-01A for serial connection to the COM1 mini-DIN RS-232 port of the covered EH3, SV2 and PM hosts. Select the COM port assigned by the USB driver. For ISPSoft, configure the connection in COMMGR.
4–20 mA scaling example
For a 4–20 mA transmitter, nominal raw values are 400 at 4 mA, 1200 at 12 mA and 2000 at 20 mA. For a 0–10 bar transmitter, use bar = (raw − 400) × 10 ÷ 1600. A raw value of 1200 corresponds to 5 bar. Set any wire-break threshold according to the transmitter’s fault behaviour.
Editor’s Note
On a used card, check the full DVP-F2AD label and the host connector. Inspect the terminals, fixing screw and slot before fitting it.
For a current input, look at the channel jumper first. Correct the wiring before changing the scaling in the program.
Test both channels with a known signal. A 5 V input should give around 2000 counts, and a 12 mA input around 1200 counts.
If readings jump, check the COM return and the shielded cable routing. Keep the signal cable away from the drive-to-motor wiring.
If the HMI reading seems frozen, monitor the present-value register first. If it responds correctly, check the average register, D1118 and the HMI scaling in that order.
PDF documents
See Delta DVP PLC files for the terminal diagrams, special registers and programming cable references.
Related cards and modules
DVP-F2DA adds two analog outputs. For four inputs, compare DVP04AD-H2, DVP04AD-H3 and DVP04AD-S2 for the applicable host family. DVP06XA-H3 combines analog inputs and outputs. Check the connection and slot type for each model.
Related topics and navigation
DVP-F2AD main page · DVP function cards · DVP expansion modules · Delta DVP PLC series · Second-hand Delta products
External references
Delta function card instruction sheet (2024, EN/ZH) · Delta DVP PLC programming manual (EN) · Delta PLC/HMI cable selection guide (EN)