Delta DVP24XP200T

Delta DVP24XP200T — 16-Input, 8-Output NPN Transistor Expansion Unit

Delta DVP24XP200T is a 100–240 V AC powered digital expansion unit with 16 inputs and 8 NPN transistor outputs, used with supported DVP-ES2 and DVP-EX2 systems. It is not a standalone PLC CPU; the host CPU runs the program and scans its I/O. The number 24 denotes the combined input/output count, not 24 outputs.

Typical signals include inductive sensors, photoelectric sensors, limit switches and pushbuttons. Outputs can switch suitable DC loads, interface relays and drive control inputs. Check the NPN/PNP wiring arrangement before connecting field devices. Do not confuse this unit with the older DVP24XP11T: similar I/O counts do not establish matching power supplies or host compatibility.

Power supply and digital inputs

Main supply: 100–240 V AC at L/N, with a listed consumption of 20 VA. The inputs use 24 V DC, approximately 5 mA. AC mains power must never be applied to an X input. The +24V/24G service supply provides up to 100 mA; include input and sensor consumption in that budget.

Input thresholds: OFF→ON above 15 V DC and ON→OFF below 5 V DC, with a 4.7 kΩ input impedance. Listed response times are 10 ms ±10% OFF→ON and 15 ms ±10% ON→OFF. The local terminals are X0–X7 and X10–X17. This is octal numbering, so there are no X8 or X9 terminals.

For NPN sensors, connect S/S to positive 24 V; for PNP sensors, connect S/S to 0 V. Connect the sensor signal to the appropriate X terminal. S/S configures the input common arrangement; it does not change the outputs from NPN to PNP. Do not directly parallel the positive terminals of the internal service supply and an external power supply.

NPN transistor outputs and current limits

The eight outputs, Y0–Y7, are NPN/sinking transistors. They are not isolated dry relay contacts and cannot directly switch AC loads. The model-specific wiring section specifies a 5–30 V DC load voltage range. Supply UP with external +24 V and ZP with external 0 V; the permitted auxiliary supply range is 24 V DC −15%/+20%. Connect the positive side of the load to its suitable DC supply and the other side to the selected Y output.

Document discrepancy: sections 2.1 and 2.5.12 of the 2026 DVP Module Manual specify 0.3 A/output and 1.2 A/common. The introduction of the same manual and some other sheets state 0.5 A/output and 4 A/common. This page adopts the lower limits for design screening. This conservative editorial choice does not establish the rating of every hardware revision; obtain revision-specific manufacturer confirmation before using the higher figures.

All eight outputs share the UP/ZP group. Observe both the individual output limit and the total common limit: eight loads at 0.3 A would total 2.4 A and exceed the adopted 1.2 A group limit. Check starting current and operating conditions, fit suitable suppression to inductive loads and provide appropriate fuse protection. The 100 mA service supply is not a high-current load supply.

Address allocation and host compatibility

This unit belongs to the ES2/EX2 expansion module family. Check the host CPU manual for its expansion count and total digital I/O capacity. A matching brand or connector does not establish compatibility with every Delta DVP series.

Local terminal labels are not necessarily the addresses used in the CPU program. For example, installed as the first digital extension after a 16-input/16-output DVP32ES200R, with no preceding expansion, this unit occupies X20–X37 and Y20–Y27. Another CPU or preceding module changes the allocation. Verify actual addresses through online monitoring during commissioning.

Programming software, cable and communications

No separate program is downloaded to DVP24XP200T. Develop the PLC program in the host CPU using WPLSoft or ISPSoft, as supported by that CPU and its version. Use the assigned X/Y addresses in the ladder program and online monitor. Analog-module CR configuration does not apply to this digital expansion unit.

For the ES2/EX2 CPU’s 8-pin mini-DIN RS-232 programming port, the manufacturer cable guide lists the UC-PRG020-12A USB programming cable. The serial alternative is UC-MS020-01A; a computer without a serial port also requires a suitable USB-to-RS-232 converter. Check the USB driver and assigned COM port, and configure COMMGR appropriately when using ISPSoft. Connect the programming cable to the CPU, not to this expansion unit.

DVP24XP200T is not a standalone Modbus RTU station and has no independent RS-485 port or station address. RS-485 communication requires the host CPU or a suitable communication module. Transistor outputs alone do not establish servo positioning pulse capability. For encoder or high-speed counter applications, select the appropriate CPU input or dedicated module.

Editor’s Note

When buying a used unit, read the complete label first. Do not accept a different suffix solely because the enclosure looks familiar. Inspect the L/N terminals, input commons, UP/ZP terminals and expansion connector separately for heat damage, corrosion and loose connections.

Have a qualified person handle energised checks. Before disconnecting wiring, isolate both the AC main supply and external DC supplies, observe the instruction sheet’s minimum one-minute wait, and verify that the circuit is de-energised. Keep mains wiring separate from the 24 V sensor and output circuits.

An illuminated input LED is only one part of the test. Apply an appropriate 24 V signal to each channel and confirm the correct X address in the host CPU. Incorrect S/S wiring or address allocation can make a healthy module appear faulty.

If an output LED is on but the load does not operate, measure UP/ZP under load first. Then test each Y output with a suitable small DC load. An LED does not prove that the transistor switches current correctly; also check for an output stuck on because of a shorted transistor.

Calculate load current per output and for the complete common group. Because the documents disagree, do not silently replace this page’s 0.3 A/output and 1.2 A/common design limits with the higher figures. Coil transients, wiring faults and an inadequate power supply can cause recurring output failures.

Check panel grounding and electromagnetic interference control. Do not rely on a standard PLC output alone for an emergency stop; provide a safety relay and disconnection circuit appropriate to the risk assessment. These are inspection suggestions, not a claim that a particular unit has been tested or certified as working.

PDF documents and related models

Delta DVP PLC files is the shared document hub for this model. The 2026 DVP Module Manual, 2024 ES2 digital I/O instruction sheet and PLC/HMI cable guide used here have been recorded with their filenames, relevant pages and document discrepancies. The archived files retain their original languages.

Related models: DVP24XP200R provides the same I/O count with relay outputs; DVP32XP200T provides 16 inputs/16 transistor outputs; DVP24XN200T is a 24-output unit. DVP08XP211T is a 4-input/4-output option and DVP16XP211T is an 8-input/8-output option. These are comparison choices, not confirmed drop-in replacements.

Related topics and navigation

DVP24XP200T main page · ES2/EX2 modules · DVP expansion modules · Delta PLC models · Delta main page

External references — manufacturer documents

DVP Module Manual — 2026, English · ES2 digital I/O instruction sheet — 2024, English/Chinese · PLC/HMI cable selection guide — English