Delta DVP16XP211T
Delta DVP16XP211T – 8 Digital Inputs / 8 NPN Transistor Outputs
Delta DVP16XP211T is a mixed digital I/O module in the DVP-ES2/EX2 expansion module family, providing eight 24 V DC inputs and eight NPN sinking transistor outputs. In a DVP-ES2 or DVP-EX2 PLC system, it collects pushbutton, limit switch and sensor signals and switches suitable DC control loads. It is an expansion module; the CPU executes the application.
The S/S input common can be wired for NPN or PNP sensors. This selection does not change the NPN output type. Check the NPN/PNP difference when replacing existing hardware. Matching I/O counts alone do not establish compatibility with a different generation of Delta modules.
Technical data and conflicting ratings
Inputs: Eight channels, 24 V DC / approximately 5 mA; input impedance 4.7 kΩ. ON threshold >15 V DC, OFF threshold <5 V DC; OFF→ON response 10 ms ±10%, ON→OFF response 15 ms ±10%.
Outputs: Eight NPN open-collector channels; load voltage 5–30 V DC. UP/ZP require an external 24 V DC supply. Listed switching delays are 50 µs for ON and 200 µs for OFF. These delays alone do not establish a high-speed pulse-output capability.
Mechanical data: Removable terminals, 35 mm DIN rail or screw mounting; width L = 70 mm, mounting-hole spacing L1 = 62 mm. Listed weight is 149 g. The instruction sheet specifies 1.6 W module consumption; field-load power must be calculated separately.
Conflicting current and frequency limits: Instruction sheet DVP-0131130-01, dated 21 February 2024, lists 0.5 A/output, 4 A/COM and a maximum of 1 kHz. The introductory table in the 6 January 2026 DVP Series Module Manual also lists 0.5 A/4 A. However, its technical table on printed page 2-3 and DVP16XP211T wiring section on page 2-15 specify 0.3 A/output and 1.2 A/COM; page 2-3 lists 100 Hz.
No verified hardware-revision distinction has been established for this discrepancy. Our recommendation is to design to the lower limits until Delta confirms the applicable ratings. This is a conservative design choice, not a newly confirmed universal manufacturer specification. Eight simultaneous loads of 0.3 A would exceed a 1.2 A common limit.
S/S, UP and ZP wiring
Upper terminals: S/S, X0–X7 and NC. For an NPN sensor, connect S/S to +24 V and the sensor output to the appropriate X terminal. For a PNP sensor, connect S/S to 0 V and the sensor output to the X terminal. Check the output type of each inductive sensor or photoelectric sensor.
Lower terminals: UP, ZP, ground, Y0–Y7 and NC. UP = +24 V, ZP = 0 V; the auxiliary supply range is 24 V DC −15%/+20%. Connect the positive side of the DC load to its suitable load supply and the other side to Y. When ON, the output sinks current towards ZP. For a different load voltage, verify the manufacturer's circuit and common-reference requirements.
Leave NC terminals unconnected. Here NC means an unused terminal, not a normally closed contact. Select the 24 V DC power supply, grounding, fuse and short-circuit protection together. Do not connect AC mains loads directly to these transistor outputs.
Relay and DC contactor coils need suitable suppression. Select the diode arrangement with the required release time in mind. Check load voltage, per-channel current and total common current together. An illuminated transistor output LED does not establish that the channel can drive its load correctly.
Addressing, programming software and cable
Address example: If the CPU and preceding modules assign X20/Y20 to this module, its inputs are X20–X27 and its outputs Y20–Y27. X0/Y0 markings on the module identify local channels. DVP X/Y addresses use octal numbering: X30 follows X27. Verify the actual starting addresses in the CPU I/O allocation; they are not identical for every CPU.
Programming: No separate application is downloaded to the module. Use WPLSoft or ISPSoft for a supported ES2/EX2 CPU, matching the software version to the CPU and existing project. ISPSoft connects through COMMGR. In PLC programming, the signals are handled as X inputs and Y outputs in the Ladder program.
Connect the cable to the CPU: The cable guide shows UC-MS020-01A (2 m) or UC-MS030-01A (3 m) for ES2/EX2 COM1 RS-232, and UC-PRG020-12A (2 m) for USB connection. Install the appropriate Windows USB-cable driver and select the assigned COM port. This module has no separate USB/RS-232 programming port or independent RS-485/Modbus station address; communication settings belong to the CPU.
Related modules
Compare DVP16XP211R with eight inputs/eight relay outputs; DVP08XP211T with four inputs/four transistor outputs; DVP16XM211N with sixteen inputs; and DVP16XN211T with sixteen transistor outputs. These serve different I/O requirements. Check load, supply and CPU compatibility before treating any candidate as a replacement.
Editor's Note
Start with a clear label photograph and the terminal markings on a used module. A similar-looking unit from another generation can create unnecessary trouble during installation; confirm the full DVP16XP211T code.
Inspect the wiring with power isolated, then begin with a current-limited 24 V supply and a low-current test load. Successful CPU communication does not prove that the outputs have their UP/ZP supply.
Test all eight inputs individually and compare the input LEDs with the online X states. The listed input delays make this an unsuitable choice for high-speed encoder counting.
Measure outputs individually, then with the intended simultaneous load. Rate the test resistor for its dissipated power. A no-load terminal voltage is not a substitute for a loaded measurement.
For a failed channel, check the field cable, coil, suppressor and common supply first. Find the load fault before repairing or replacing the output stage; otherwise the replacement may fail again.
For a used-unit sale, provide quantity, label photographs, working/faulty condition and test results. Sales require an invoice; no returns; workshop testing is available. Sellers can send details to otomasyonavm@gmail.com.
PDF documents and related topics
Visit our Delta DVP PLC files page first. This model's archive record includes the DVP-ES2 DIDO instruction sheet (21 February 2024, 19 pages, English and Chinese), DVP Series Module Manual (6 January 2026, 913 pages, English; especially printed pages 2-3 and 2-15) and PLC/HMI Cable Selection Guide (15 August 2019, 175 pages, English; printed page 1-3).
For the wider automation system and CPU selection, see Delta DVP PLC series and Delta PLC. Further model information is grouped on the DVP16XP211T model page.
Navigation: Delta home | DVP series | ES2/EX2 modules | DVP PDF files
External references
Delta DVP-ES2 DIDO original instruction sheet – distributor archive
Delta DVP Series Module Manual – 2026 edition, distributor archive
Delta PLC/HMI Cable Selection Guide – DigiKey archive
Delta – ISPSoft and WPLSoft explanation