
Crane safety: make the right decisions before the load leaves the ground
Crane safety addresses more than a falling load. It also covers overturning, crushing, collisions and electrical hazards. A safe lift needs a suitable crane, appropriate rigging, a competent team and a controlled operating area. A machine that runs is not necessarily ready for the proposed lift.
1. Assess the load, the rating and the rigging together
Establish the load weight, centre of gravity, attachment points and travel route before lifting. The capacity assessment must include slings, lifting beams and other below-the-hook equipment. A boom crane's permitted load depends on its working radius and configuration; an overhead crane must remain within the relevant hoist rating. An advertised maximum tonnage is not a rating for every operating condition.
Select lifting accessories for the actual hitch and sling angles. As sling legs become more horizontal, their tension increases. The centre of gravity can also prevent equal sharing between legs. Protect slings appropriately at sharp edges. A crane scale or load cell can provide useful weight information, but it is not automatically an overload protection system.
2. Match the site assessment to the crane
For a mobile crane, assess ground bearing capacity, outrigger setup, slopes, excavation edges and underground voids. For an overhead crane, consider runways, supporting structures, travel limits and other cranes sharing the space. Crane type determines the relevant selection and installation questions; the same checklist will not fit every arrangement.
Outdoor lifts must account for wind and the load's exposed surface area. A broad sheet can behave differently from a compact object of the same weight. Plan work near overhead power lines with the network owner; do not estimate a safe clearance. Electrical danger can arise without direct contact. There is no single wind limit or clearance suitable for every crane and job.
3. Control access to the entire load path
Keep people out from under suspended loads and do not carry loads over them. Control access to the travel route, swing area and landing zone. Allow for crushing hazards between the load and walls, machines or stored material. Keep hands clear of the underside of the load and the space between a tensioned sling and the load. Select helmets, gloves and protective footwear for the assessed risks; they do not make the space beneath a suspended load safe.
Do not use an ordinary hoist lift to drag a load sideways, wrench a trapped component free or apply shock loads through abrupt reversals. Standard material-lifting hooks and slings must not be used to carry people. Special operations, such as lifting one load with two cranes, require specific planning and coordination.
4. Agree who gives motion commands—and who can call stop
The operator needs training, experience and authorisation appropriate to the equipment and task; documentary requirements depend on local rules. Appoint a signal person where needed and agree the signals before starting. Motion commands come from the designated signal person; anyone who sees a hazard can call for a stop. If required communication or visibility is lost, stop the operation safely. Do not guess an unclear command.
Check that crane radio controls operate the intended crane, have clear direction markings and respond correctly to stopping commands. Commands for neighbouring cranes must not become confused. Wireless control does not remove the need to see the load or use an appropriate signalling arrangement.
5. A recent inspection does not replace today's pre-use checks
Follow the manufacturer's instructions when assessing ropes or chains, hooks, slings, brakes, controls and protective functions. Do not start if a defect is suspected. The upper protective limit must not become the routine stopping method, and protective devices must not be bypassed. Maintenance and repair and any required formal inspections serve different purposes. A previous satisfactory report does not cancel a defect found today.
6. Emergency stopping, STO and load holding have different jobs
An emergency stop must stop hazardous motion in the manner established by the risk assessment. Safe Torque Off (STO) prevents the motor from producing torque through a safety-related function. It does not hold a gravity-driven load by itself and does not provide electrical isolation. A suitable mechanical holding brake and any necessary additional safeguards are part of keeping the load secure.
The crane drive, encoder feedback and brake coordination must work together. Where a safety relay or safety controller is used, validate the complete safety function; a stop command in a standard PLC program is not a substitute for that assessment. Handle regenerated energy appropriately during lowering. A braking resistor dissipates energy as heat; it cannot mechanically hold the load.
7. Protect the area when something goes wrong
Load drift, rope damage, unexpected motion, protective-device failure or communication loss calls for stopping the operation and keeping the danger zone clear. Do not improvise a recovery by releasing a brake or bypassing protection to lower a stranded load. Use the equipment-specific emergency procedure and a competent recovery team. Maintenance requires energy isolation, lockout and tagout; an emergency stop does not replace these measures.
If contact with an overhead power line is suspected, keep people away from the crane, load and surrounding hazard area. Follow the site emergency plan and the network owner's directions. Plan safe operation around applicable standards, the equipment instructions and local requirements.