What is BS EN 55014?

What Is the BS EN 55014 Standard?

Emitted interference and resistance to disturbances

A vacuum cleaner interfering with nearby electronics and a control board restarting because of an external electrical disturbance illustrate two different aspects of electromagnetic compatibility. The BS EN 55014 family addresses emission and immunity requirements for household appliances, electric tools and similar equipment. Its purpose is to support acceptable operation in the specified electromagnetic environment while keeping the disturbances generated by the product within defined limits.

Naming and current editions

BS identifies the UK national adoption, while EN identifies a European standard. The IEC designation in the current titles indicates their international origin. The underlying international documents are CISPR 14-1 and CISPR 14-2, developed within the IEC framework. Technical documentation should use the complete document reference and edition rather than the shorthand “IEC 55014”.

The editions currently listed by BSI are BS EN IEC 55014-1:2021 and BS EN IEC 55014-2:2021. Their international counterparts are CISPR 14-1:2020 and CISPR 14-2:2020, respectively. When reviewing an older test report, a statement such as “complies with 55014” is insufficient: check the part, year, amendments and product scope together.

Part 1: Emissions generated by the equipment

Emission requirements based on CISPR 14-1 address radio-frequency disturbances generated by the product. EMC emissions are assessed through conducted paths along connections or radiated paths through electromagnetic fields. Motor commutation, switching power supplies and electronic power controls can generate electromagnetic interference. Test methods, measurement ranges and limits depend on the product characteristics and applicable provisions; one measurement plan does not suit every device.

Part 2: Immunity to external disturbances

Immunity requirements based on CISPR 14-2 assess how equipment responds to external electromagnetic influences. Noise immunity means more than simply finding that the product still works after testing: it must meet the specified performance criteria during and after the tests. Whether a temporary change in operation is acceptable depends on the applicable criterion and the product function.

A test plan may include electrostatic discharge representing user contact, radiated RF fields associated with nearby transmitters, and conducted RF disturbances coupled onto cables. Other methods address switching events through EFT/burst, high-energy transients through surge, and supply interruptions through voltage dips and short interruptions. Applicable tests and levels are selected from the relevant product standard according to equipment category, power supply and ports.

Editor's note: A device can pass emission testing and fail immunity testing. Generating little interference and resisting external interference are different characteristics. Also, EMC compliance does not replace an electrical safety assessment.

Harmonics and product scope

Mains harmonic currents require a different assessment from the RF emission measurements in 55014-1. Within the EN/IEC 61000 family, 61000-3-2 addresses harmonic current emissions, while 61000-3-3 addresses voltage changes, fluctuations and flicker for equipment within their respective scopes. Input current, supply connection and scope conditions must be checked separately. A harmonic filter and an RF interference filter should not be assumed to solve the same problem.

The 55014 family is not a universal standard for electrical equipment. Equipment intended exclusively for industrial environments is excluded. Multimedia equipment, measurement and control equipment, and motor drives may fall under different EMC standards. Multifunction products may need relevant provisions from more than one standard; selection depends on functions, intended environment and scope definitions rather than the product name alone.

From test reports to product conformity

For a variable-speed electric tool, for example, the test plan should identify operating modes, loads and accessories. Cable routing, enclosure, PCB layout and planned earth connections should represent the actual product configuration. An EMC filter may help, but adding one does not itself prove compliance. Component reports support the design; they do not automatically complete the assessment of the finished product.

For CE marking, the manufacturer identifies applicable legislation and prepares technical documentation, conformity evidence and an EU declaration of conformity. It is incorrect to assume that every product requires an independent “BS EN 55014 certificate”. An accredited laboratory report can provide strong technical evidence; the required assessment route depends on the applicable legislation.

A current edition in the BSI catalogue does not automatically provide a legal presumption of conformity. For the EU, check harmonised standard references and transition dates; for Great Britain, check the designated standards records. The relevant conditions are those applying when the product is placed on the market.

Related topics

EMI filters; RFI filters; CISPR 32; the IEC/EN 61326 family; the IEC 61800 family.


Refine Search