6GK1 901-1BB20-2AE0

Siemens 6GK1 901-1BB20-2AE0 – IE FC RJ45 Plug 90, 2×2

The 6GK1 901-1BB20-2AE0 is the 50-piece ordering code for the SIMATIC NET Industrial Ethernet FastConnect RJ45 Plug 90. This metal-bodied connector is designed for IE FC TP 2×2 cables and has a 90° cable outlet. It provides a physical cable connection for ET 200 stations, PLCs and other industrial network devices equipped with a suitable RJ45 interface.

Understanding 2AE0, 2AB0 and 2AA0

For the same 90° plug, 6GK1901-1BB20-2AA0 specifies one piece, 6GK1901-1BB20-2AB0 ten pieces, and 6GK1901-1BB20-2AE0 fifty pieces. These suffixes do not identify different transmission speeds or port counts. For used parts or opened packs, compare the manufacturer's pack code with the actual quantity offered.

6GK1901-1BB10-2AA0 is a different housing arrangement with a straight 180° cable outlet. When selecting used connectors, consider pack quantity and outlet angle separately. Two RJ45 plugs can require different clearances inside the cabinet.

10/100 Mbit/s and two-pair cabling

The specified transmission rates are 10 and 100 Mbit/s. 2×2 means two pairs, or four conductors in total. Do not select this model as a four-pair Gigabit Ethernet plug. When assessing an Ethernet connection and its supported speed, check the connector, cable and device port together.

The Siemens data sheet specifies AWG22 / approximately 0.33 mm² conductors in IE FC TP 2×2 installation cable and a 6.5 mm cable diameter. This does not make arbitrary office patch cables suitable. The conductor construction and outer jacket must match the FastConnect termination system. The permitted cable length also depends on the cable type and complete connection arrangement, rather than the plug alone.

90° outlet and ET 200 compatibility

The angled outlet helps route the cable away from the front of the socket. Nevertheless, check surrounding clearance, adjacent ports and the cable's bending allowance. Electrical compatibility is insufficient if the fitted connector prevents a cover from closing or leaves the cable under continuous sideways tension.

Connection formats vary across the ET 200 family. This plug can serve suitable RJ45 PROFINET connections; it does not replace a PROFIBUS-DP connector or an M12 plug. Check the interface type, connection arrangement and required accessories against the exact station model.

FastConnect termination

The cable is not crimped in the same way as a conventional transparent RJ45 plug. FastConnect uses insulation-displacement contacts to contact suitable insulated conductors. Prepare the cable end to Siemens' assembly template, insert the conductors according to the connector's color markings and close the contact elements fully.

For effective shielding and strain relief, the cable screen must seat against the shield contacts and the outer jacket must engage the strain-relief feature. An assembly that holds the cable only by its individual cores is incorrect. Close the locking mechanism completely without damaging the latch spring. Perform assembly with the cable de-energized.

Housing, environment and PoE

Dimensions are 13.7 × 16 × 42 mm, in width, height and depth order; net weight is 35 g per plug. The IP20 rating does not make the metal housing waterproof. Siemens' 2022 data sheet specifies an operating range of −40 to +85 °C; any lower limits of the cable or connected equipment still apply.

The data sheet lists PoE and PoE+ capability. The plug does not generate power, and using it does not make an ordinary Ethernet port a PoE source. The supplying device, receiving device and cable arrangement must also be compatible. The connector has no IP address, software or communication settings of its own.

Retermination and troubleshooting

The assembly instructions allow the insulation-displacement contacts to be released and reconnected up to ten times. This is not the connector's RJ45 mating-cycle rating. Previously pierced cable ends must be cut off and freshly prepared before retermination. For intermittent link loss, inspect conductor seating, shield contact, locking and cable strain before checking the device port's link status.

Editor's Note: Keep three details separate: 2AE0 identifies a fifty-piece pack, 2×2 describes four-conductor cabling, and 90° specifies the cable outlet angle. A sound metal housing does not justify reconnecting an already pierced cable end. Correctly preparing a fresh cable end is part of a proper repair.

Manuals and related topics

For the product data sheet and multilingual assembly instructions, including Turkish, visit Siemens ET 200 manuals and PDF documents. References: Siemens 6GK1901-1BB20-2AE0 Data Sheet, 10 October 2022; IE FC RJ45 Plug 90 Assembly Instructions, A5E0328643-06, January 2022.

Industrial communication · Ethernet frequently asked questions · HMI panels · SCADA systems

Navigation: Siemens automation · SIMATIC S7 · Siemens ET 200 · OtomasyonAVM home