6ES7 122-1FA00-0AA0
6ES7 122-1FA00-0AA0 – Siemens SIMATIC SC AC Output Module
Series: SIMATIC SC / ET 200L-SC / ET 200L-SC IM-SC
Category: AC digital output electronic module
Description and system role
6ES7 122-1FA00-0AA0 is a digital output module for the Smart Connect (SC) architecture within the Siemens ET 200 family. It switches AC loads electronically. Load selection must account for its AC operating conditions and minimum current requirement, rather than treating it as a mechanical relay's dry contact.
Commands originate in the PLC program and reach the module over the station's SC bus. In a SIMATIC S7 project, check the station, slot and output address together. When reviewing the ET 200 system architecture, distinguish the SC electronic module from the station's communication interface.
Technical specifications
Output: 1 channel, rated 1 A. Load voltage: 120/230 V AC. Frequency: 47–63 Hz. Switching: zero crossing. Dimensions: 10 × 64 × 51 mm (width × height × depth); weight: approximately 15 g.
The Siemens operating manual specifies 40 mA–1.1 A at 0–40 °C and 40 mA–0.6 A at 40–60 °C. In a warm cabinet, size the load for the applicable temperature range rather than relying solely on the nominal front-label rating.
Off-state residual current: maximum 3 mA. Internal output short-circuit protection: none. Select external protection and wiring for the connected load and the manufacturer's installation requirements.
Terminal base and supply
The module can be used with TB16SC and TB16IM-SC bases. TB16SC is available with screw terminals as 6ES7 120-0AH01-0AA0 and spring terminals as 6ES7 120-0BH01-0AA0. The corresponding TB16IM-SC versions are 6ES7 120-0AH50-0AA0 and 6ES7 120-0BH50-0AA0.
Check the terminal base and connection components against the installed station. Use this product's wiring diagram to identify terminal functions; another SC module may have a different assignment.
This electronic module requires no additional L+/M supply. That does not remove the station's overall need for a 24 V DC power supply. Assess the AC load circuit and station supplies separately. Isolate the relevant circuits and verify the absence of voltage before wiring.
Load selection and application
When driving an interposing relay or contactor coil, check coil voltage, pickup current, holding current and suppression together. For small electronic loads, the power rating alone is insufficient; verify reliable turn-on and turn-off as well.
Zero-crossing switching does not provide triggering at an arbitrary phase angle on command. Do not select this module as a phase-angle controller. Check the complete order number when buying a replacement; a similar-looking DC output or relay module should not be assumed interchangeable.
Configuration and fault checks
PROFIBUS communication is handled by the station. Back up the project and record the module sequence and output address before replacement. Digital input and analog input modules in the same system still require their own wiring and configuration.
The module has a green status LED and no interrupt or diagnostic functions of its own. Compare the command shown on an HMI or SCADA screen with the PLC output state and suitable measurements at the load. Healthy station communication does not rule out a supply, wiring or load fault.
Editor's Note
A sensitive meter may show voltage while the output is off without the module being faulty. Residual current and the connected load can affect the reading. If a small coil fails to release or an indicator remains illuminated, investigate load compatibility first. Do not add an arbitrary resistor for testing: an additional load on a mains circuit requires proper power, insulation and thermal assessment.
PDF manuals and technical references
Section 10.5 of the ET 200L, ET 200L-SC and ET 200L-SC IM-SC manual covers this model. Visit Siemens ET 200 PDF and user manuals for the documentation page.
Related topics
ET 200 digital outputs · ET 200 terminal blocks · ET 200 connection modules · ET 200 additional modules · About ET 200
Quick links: Siemens ET 200 · Siemens S7 · Siemens S7 PLC · PLC and HMI · OtomasyonAVM home