6ES7 194-1LY00-0AA0
Siemens 6ES7194-1LY00-0AA0 ET200 5-Core PVC PROFIBUS and Power Cable
Siemens 6ES7194-1LY00-0AA0 is a standard five-core cable with a PVC sheath for bus signals and power connections in ET200 systems. The manufacturer describes it as unprepared cable, with the required length and end connections determined by the application. Documentation may also show the order number as 6ES7 194-1LY00-0AA0.
Role in an ET200 system
The cable is used where PROFIBUS communication and field device power connections are carried together. Siemens lists it among ET200X accessories in the ST40 catalog and in the PROFIBUS network components table of the ET200S IM151-7 CPU manual. Suitability therefore depends on the station's connection arrangement as well as its product family.
When preparing a connection between a PLC and a field station, check the PROFIBUS interface, connectors and supply terminals together. Membership of the ET200 family alone does not establish compatibility with every device or interface in that family.
PROFIBUS and supply conductors
In the SIMODRIVE POSMO A connection arrangement for which Siemens recommends this order number, the manual shows shielded 2 × 0.35 mm² conductors for PROFIBUS and 3 × 0.75 mm² conductors for the electronics supply. This describes the separation of signal and supply conductors in that application. Terminal and pin assignments must follow the wiring diagram of the connected equipment.
The data conductor shield and bus layout both matter when assessing communication wiring. When reviewing an RS-485 connection arrangement, distinguish the functions of the data pair, signal reference, shield and protective earth. Preserve conductor insulation and shield integrity when preparing the cable ends.
Connector selection and cable preparation
Unprepared cable requires termination for the selected equipment and connectors. Cutting, stripping, shield termination and conductor connections must follow the instructions for the relevant connection hardware. If an assembled cable is required, specify the connector types, the wiring at both ends and the finished cable length.
The 6ES7194-1AA00-0XA0 connection plug, listed among ET200X accessories, is a separate component for PROFIBUS, control and auxiliary supply connections. When considering it with this cable, verify the station connection and the applicable assembly instructions.
Difference between 1LY00 and 1LY10
6ES7194-1LY00-0AA0 is the standard PVC-sheathed version. Siemens describes 6ES7194-1LY10-0AA0 as the PUR-sheathed version with oil resistance and suitability for trailing applications; resistance to welding conditions is conditional. These properties belong to the 1LY10 model. For moving cable carriers, oily environments or welding areas, select the complete order number against the relevant application requirements.
Length specification and route planning
Older Siemens ordering tables show 6ES7194-1LY00-0AA0-Z, with -Z indicating that the required length must be specified in metres. A quotation request should state the total length, the number of separate pieces and whether end preparation is required.
Assess both communication requirements and voltage drop on the power supply side when planning the run. Determine the required length from the actual route, termination allowances and maintenance access. Verify the permitted network segment length and supply load against the relevant system and equipment documentation.
Editor's note
Check the complete order number, PVC or PUR sheath, required length, end connections and operating environment together. For an existing installation, compare the cable marking with the equipment wiring diagram. Manufacturer connection information is available through the Siemens ET200 manuals section. Availability, supplied length and connector preparation should be confirmed with the quotation.
Related topics
For control and monitoring, explore PLC and HMI systems, operator panels and SCADA. For system research, see Siemens S7-300, about Siemens ET 200 and ET 200 PROFIBUS and PROFINET.
Other module groups: ET 200 analog input modules · Digital input modules · Digital output modules · Connection modules · Additional modules.
Navigation: Siemens ET 200 · Siemens SIMATIC S7 · Siemens S7 PLC · OtomasyonAVM home