6ES7 193-4CA80-0AA0

Siemens 6ES7193-4CA80-0AA0 ET200S TM-E15N26-A1 FastConnect Terminal Module

Siemens 6ES7193-4CA80-0AA0 is the TM-E15N26-A1 universal terminal base for 15 mm wide electronic modules in the ET200S system. It uses FastConnect termination and provides twelve terminals in a 2 × 6 arrangement. The AUX1 bus continues through the base and can be accessed at dedicated AUX1 terminals. The order number also appears as 6ES7 193-4CA80-0AA0.

FastConnect termination and base function

The Siemens manual describes FastConnect as a connection method that does not require the conductor insulation to be stripped. Check conductor suitability and the installation procedure against the instructions for this connection type. Use the exact terminal base designation when preparing the wiring, since conductor preparation for another terminal technology may differ.

The terminal base provides the mechanical and electrical connection for the electronic module. The backplane bus and the power buses from the power module continue through it. When selecting parts for a PLC station, assess the electronic module's order number, field wiring and base dimensions together.

The twelve terminals and AUX1 connections

Terminals 1–8 connect to the electronic module. The fitted module determines their signal assignments. A3, A4, A7 and A8 are connection points on the same AUX1 bus. Pay attention to the full marking when distinguishing terminals such as 3 and A3, or 4 and A4. Reading only the number can lead to an incorrect connection.

Trace the potential distributed through AUX1 using the station wiring diagram. The four AUX1 terminals provide access to a common bus, so separate, unrelated potentials must not be connected to them. When reviewing the power supply arrangement, check signal terminals and common potential connections separately.

Electronic modules and channel count

The 2 × 6 designation describes the physical terminal arrangement. The electronic module determines the I/O channel count. For example, the Siemens manual for the 6ES7134-4LB02-0AB0 2AI U HF explicitly lists 6ES7193-4CA80-0AA0 as a usable terminal base for that two-input voltage module.

In this example, the electronic module performs the analog signal measurement. Its documentation defines the measuring range and terminal use. For a different module, check the relevant compatibility table, wiring diagram and AUX1 requirements again.

Differences from 4CA40 and 4CA50

In the same family, 6ES7193-4CA40-0AA0 is the TM-E15S26-A1 screw terminal version. 6ES7193-4CA50-0AA0 is the TM-E15C26-A1 spring terminal version. All three have a 2 × 6 terminal arrangement and AUX1 connection points; the 4CA80 uses FastConnect termination.

The screw and spring versions are 157 mm high, while the FastConnect version is 202 mm high. When planning a replacement, consider cabinet space, cable duct clearance and conductor reach as well as the termination method. Membership of the same product family does not remove the need to check the existing wiring and mounting arrangement.

Dimensions, weight and packing quantity

The TM-E15N26-A1 measures 15 × 202 × 43 mm, width × height × depth. One module weighs approximately 95 g. Siemens specifies a standard packing unit of five terminal modules for this order number. State whether the requested quantity refers to individual modules or complete packs when asking for a quotation.

Editor's note

Check the TM-E15N26-A1 designation, FastConnect termination and use of the AUX1 terminals together. The existing base's label, the electronic module's order number and a photograph of the connections help identify the required part. Refer to the Siemens ET200 manuals section for terminal diagrams. Stock, product condition and the quantity to be supplied should be confirmed when requesting a quotation.

Related topics

For control and monitoring, explore PLC and HMI systems, operator panels and SCADA. For system research, see Siemens S7-300, about Siemens ET 200 and ET 200 PROFIBUS and PROFINET.

Other module groups: ET 200 analog input modules · Digital input modules · Digital output modules · Connection modules · Additional modules.

Navigation: Siemens ET 200 · Siemens SIMATIC S7 · Siemens S7 PLC · OtomasyonAVM home