6ES7 181-0AA01-0AA0
Siemens 6ES7 181-0AA01-0AA0 – BT 200 PROFIBUS-DP Tester
The 6ES7 181-0AA01-0AA0 is the SIMATIC DP BT 200 portable bus test device. It is used to inspect PROFIBUS-DP installations during installation, commissioning and troubleshooting. It is service equipment for examining cabling and communication interfaces, rather than an I/O module installed alongside an ET 200 station.
Which faults can it help locate?
The BT 200 checks for broken conductors, shield discontinuity, reversed A/B conductors, short circuits and incorrect termination. It can investigate reflection points; station testing provides information about the RS-485 driver, 5 V supply and RTS signal. These functions help distinguish cable or connector problems from faults in a device interface.
A station responding to a test does not establish that every machine function works correctly. Addressing, hardware configuration, the user program and process behavior require separate assessment. A BT 200 result is part of troubleshooting; it is not a complete functional acceptance test for the system.
Its role in ET 200 and S7 systems
First identify the network used by the particular ET 200 system. The BT 200 is intended for suitable electrical PROFIBUS-DP/RS-485 networks; it should not be selected as a PROFINET or Ethernet cable tester. Several networks may coexist in a plant, without being testable using the same instrument.
Consider the ET 200 interface, connection module, additional modules and cable route together. In an S7-300 installation, knowing the CPU model alone is insufficient; identify the actual port and bus segment to be tested.
Connection conditions depend on the test
For wiring tests, connected stations must be powered down and the appropriate test connector used. Individual station tests use the dedicated cable to a powered station; the manual requires RUN for a master test. For branch tests, disconnect masters, maintain termination and select the correct baud rate. Reflection tests require no bus traffic, powered termination and removal of the test connector. Follow the manual's preparation steps for the selected test.
Length measurement requires more than 15 m of cable and cannot operate through repeaters. Cable electrical parameters affect the result. Compare the measured distance with the actual cable route.
Interface, speed and operating conditions
The unit has a 9-pin female D-sub interface and a specified rate range of 9.6 kbit/s to 12 Mbit/s. It operates from an internal rechargeable NC battery. Siemens' 2017 data sheet specifies IP20 protection and an operating range of +5 to +45 °C. It should not be treated as a weatherproof or washdown-rated field instrument.
For a used unit, a working display alone is insufficient evidence of condition. Inspect battery charge retention, keys, sockets and measurement behavior on a known-good bus. A sales description should state which checks were actually performed; untested functions should not be assumed operational.
Charger, test connector and logging accessories
Siemens' delivery description includes a test cable and test connector; the charger is ordered separately. The listed 230 V charger is 6ES7193-8LA00-0AA0, and the spare test connector is 6EP8106-0AC20. Check the actual accessories supplied with a used unit.
The logging function stores test results for transfer to a computer using suitable cabling and software. The product description's “protocol kit” refers to this reporting accessory; it should not be interpreted as unrestricted live telegram analysis. Compatibility of the old software with a current computer also requires verification.
Editor's Note: Look beyond the tester housing when buying a BT 200. A missing or faulty battery, charger, test connector or correct cable can limit its practical use. When troubleshooting, identify the test first: wiring tests and powered station tests require different preparation.
Manuals and related topics
For operating procedures and technical documents, visit Siemens ET 200 manuals and PDF documents. References: Siemens BT 200 Physical Bus Test Device, April 2000; product data sheet, 16 March 2017; PROFIBUS Network Manual, April 2009; PCS 7 Service Support and Diagnostics, March 2009.
Industrial communication · What is a PLC? · HMI panels · SCADA systems
Navigation: Siemens automation · Siemens S7 PLC range · SIMATIC S7 · Siemens ET 200 · OtomasyonAVM home