6ES7 953-8LG11-0AA0
Siemens 6ES7 953-8LG11-0AA0 – 128 KB SIMATIC Micro Memory Card
The 6ES7 953-8LG11-0AA0 is a 128 KB SIMATIC Micro Memory Card with 3.3 V NFlash memory. Siemens identifies it for S7-300, C7 and ET 200S IM151 CPU applications. Check the exact target device order number and its supported card type before selection. 128 KB does not mean 128 MB.
Load memory versus work memory
In compatible CPUs, the MMC provides nonvolatile load memory for program blocks, hardware configuration and related system data. The stored program survives a power interruption. Work memory inside the CPU is a separate area used to execute the program; this card does not expand CPU RAM or increase processing speed.
Assess the CPU module and memory card separately. The project's load memory requirement must fit the card, while its work memory requirement must fit the CPU. Installing a larger card does not automatically make a PLC program run when its work memory requirement exceeds the CPU's limit.
Different roles in ET 200S and ET 200M
The ET 200S IM151-7 CPU manual requires an inserted SIMATIC MMC for loading the user program and operating the CPU. However, interfaces and I/O modules throughout the ET 200 family do not all use this card. Select the interface type, connection module and additional modules against the actual station hardware.
The ET 200M IM153-4 PN manual also lists this exact order number among supported MMCs. One role of the card in that interface is storing the PROFINET device name. The manual states that 64 KB is sufficient for the name, so a 128 KB card has sufficient capacity for this purpose. This differs from a CPU using a card to hold its user program.
Is it large enough for a firmware update?
Updating IM153-4 PN firmware through an MMC requires at least 2 MB. Consequently, the 128 KB 6ES7953-8LG11-0AA0 can hold the device name but is too small for that firmware update procedure.
The October 2011 IM151-7 CPU manual specifies at least 4 MB for firmware backup and update using an MMC. Read capacity requirements for the particular device and operation; a requirement for one ET 200 station must not be applied to every model.
Do not format it with Windows
A SIMATIC MMC is not a general-purpose storage device that can be replaced simply by selecting an ordinary SD or microSD card. Decline Windows formatting prompts and do not apply FAT or FAT32 formatting. Siemens warns that formatting with Windows destroys the internal structure required for SIMATIC use and can make the card unusable in an S7 CPU.
Use Siemens software and programming equipment supported for the relevant CPU and SIMATIC MMC. A CPU memory reset and card formatting are different operations. A STOP indication or memory reset request is not, by itself, a reason to erase the card.
Program backup and card replacement
A card containing a working program does not necessarily contain a complete, editable STEP 7 project archive with all comments and symbols. Such an archive must have been saved separately. Preserve the existing contents and engineering project before replacement; a blank replacement card cannot recover a lost machine program.
On S7-300 CPUs using an MMC, removing the card during RUN can put the CPU into STOP, and removal during a write operation can corrupt data. Schedule replacement during a planned shutdown, verify that no write operation is active and follow the exact CPU manual. The replacement card's program must match both the CPU and the machine's actual hardware and application.
The capacity printed on the label is only one selection criterion. Recognition by the SIMATIC system, compatibility with the target device and correct program contents also matter. A card previously used in another machine should not be put straight into service merely because it carries the same order number.
Editor's Note: Establish three things before selecting this card: the target device, the data to be stored and the required capacity. A 128 KB load memory card does not provide an extra 128 KB of RAM. Preserving the existing contents matters as much as choosing the correct replacement; do not accept a computer's formatting prompt.
Manuals and related topics
For the data sheet and relevant operating documents, visit Siemens ET 200 manuals and PDF documents. References: Siemens product data sheet, 20 January 2020; IM151-7 CPU, October 2011; ET 200M, April 2022; S7-300 CPU 31xC and CPU 31x installation manual, June 2008, and technical specifications, March 2011.
Industrial communication · PROFIBUS and PROFINET · Ethernet · HMI panels · SCADA systems
Navigation: Siemens automation · Siemens S7 PLC range · SIMATIC S7 · Siemens ET 200 · OtomasyonAVM home