6ES5 432-4UA11

Siemens 6ES5 432-4UA11 — 32-Channel 24 V DC Digital Input Module with Group Signal

6ES5 432-4UA11 is a 32-channel, 24 V DC digital input module for the Siemens SIMATIC S5 U series. Its digital inputs form four galvanically isolated groups of eight. Rated input current is 8.5 mA, and suitable settings provide group-signal and process-interrupt functions.

The compact U design is documented for S5-135U, S5-150U and S5-155U controllers and their U-series expansion units. In a SIMATIC S5 installation, assess CPU operating mode, interrupt support and module settings alongside channel count. When reading relay, contactor auxiliary-contact and interposing-relay states, the signal circuit must match the 24 V DC input levels.

Signal levels and group isolation

Logic 0 is defined as −33 to +5 V and logic 1 as 13–33 V. 5–13 V is not a guaranteed logic state. Typical input resistance is 2.8 kΩ. Galvanic isolation is between eight-input groups; the 32 channels are not all individually isolated.

Selectable delay and cable length

Switch block S5 selects a 3 ms, 1 ms or 0.3 ms delay for each input byte. The corresponding specified maximum input frequencies are 100 Hz, 300 Hz and 1 kHz. CPU reading and interrupt-processing conditions must also be considered when assessing pulse detection.

Maximum unshielded field-cable lengths are 600 m at 3 ms, 200 m at 1 ms and 50 m at 0.3 ms. Selecting a shorter delay changes the cable-length condition too. The specified supply range for two-wire BERO sensors is 22–33 V; compare sensor leakage and input thresholds separately.

Group signal, interrupt and the UA11 distinction

The module supports normal digital input, group-signal input, interrupt input and mixed operation. S3 selects signal edges, S1 selects interrupt lines, and S2 with X3 determines the master/slave arrangement. Group-signal and interrupt processing depend on the CPU and its operating mode.

On 6ES5 432-4UA11, jumper X4 must remain inserted, or ON, even in interrupt operation. Do not transfer the 432-4UA12 option of removing X4 to free IB 0 to the UA11 version. The wiring diagram’s X20 enable-selection jumper is also specified for UA12 only.

Addressing and interrupt program

S4 selects the start address; the 32 inputs occupy four bytes: n, n+1, n+2 and n+3. For group-signal or interrupt operation, the manual specifies the 128–255 address range. For example, a module starting at 128 uses bytes 128–131; this is an example rather than an assumed address for the installation.

During interrupt processing, read the four peripheral bytes in ascending order; repeated access to the same bytes can cause loss of interrupt capability. Review the PLC program and input/output assignment accordingly. Confirm the suitable S5 rack, interrupt-capable slot, interface connection and expansion arrangement against the system manual.

F+/F− enable input and front connections

The F+/F− enable input is rated at 24 V DC, with a 13–33 V logic-1 range and 5 mA rated current. The diagram identifies F+ as terminal 1 and F− as terminal 2. Check each eight-input group’s return separately. Missing enable or a removed connector does not ensure reliable logic-0 readings; the manual highlights logic-1 readings and QVZ fault handling under these conditions.

Within the 42-pole connector family, 497-4UA12 is a 20 mm crimp option and 497-4UB12 is a 40 mm screw-terminal option. When selecting S5 cables and connections, check connector width, rack arrangement and pin assignment together. During fault diagnosis, compare LED state, enable voltage and program data; establish safe machine conditions before testing.

Differences between related modules

430-4UA11 also has 32 inputs at 24 V DC, but must not be assumed to provide the 432 module’s group-signal and interrupt arrangement. 431-4UA12 has sixteen 24–60 V DC inputs, while 436-4UA11 belongs to the AC input family. Compare input voltage, grouping, interrupt function and hardware suffix when choosing a replacement.

Editor’s note

Give this card more attention than a basic 32-input module. Its group-signal and interrupt settings work together with the machine program. Photograph the switches and jumpers before removal so a replacement starts with a reliable record.

If eight channels fail together, inspect that group’s return and field cable first. If the whole module appears unavailable, check F+/F− enable and the front connector too. One missing connection can make a healthy card look faulty.

UA11 and UA12 may look similar, but keep the X4 rule clear. X4 must remain inserted for interrupt operation on UA11. Do not copy a jumper setting from UA12 without checking the version.

Do not assume selecting 0.3 ms will solve every problem. The unshielded cable limit at that setting is 50 m; it does not share the 600 m condition of the 3 ms setting. Assess the application and cable together first.

For a used card, testing input LEDs alone is not enough. Check all 32 channels, all four groups and the group-signal or interrupt function required by the application. If interrupts are missing, inspect address order, CPU mode and program access before setting the card aside.

OtomasyonAVM resources and PDF files

+ S5 PDF files and user manuals · About Siemens S5 PLCs. The main reference is the Digital Input/Output Modules Instructions in U Periphery, 6ES5 998-0PC22. Operating modes are on printed pages 7–12 / PDF 210–215; exact UA11/UA12 specifications and wiring are on 39–40 / PDF 242–243. The document is in English.

Related topics

+ 432-4UA12 · 430-4UA11 · 431-4UA12 · 436-4UA11 · PLC fault diagnosis.

Browse SIMATIC S5

+ S5 digital input modules · S5 racks · S5 interface modules · Siemens S5 PLC · Siemens second-hand equipment.

Siemens and external references

+ Siemens U Periphery — 6ES5 998-0PC22, Digital Input/Output Modules Instructions, Sections 1.3.3 and 5.4. PDF pages 210–215: operating modes and UA11 X4 note; PDF pages 242–243: exact UA11/UA12 specifications and wiring. English.

+ Siemens Industry Mall — 6ES5432-4UA11: exact-model record confirming 32 inputs, 24 V DC, galvanic isolation and group signal. English.