How long will my UPS last?

Work out how long your equipment can run during an outage

A UPS’s battery runtime depends on actual connected load, usable battery energy, state of charge and battery condition. A label stating 750 VA, 1,000 VA or 3 kVA does not specify minutes of backup. Two units with the same output rating can deliver different runtimes because their battery configurations differ. The UPS topology also matters for equipment compatibility and transfer behaviour.

Editor’s note: Output capacity describes how much load the UPS can supply at once. Runtime describes minutes of battery operation. Battery service life describes years of useful service. A higher VA rating alone does not guarantee longer runtime.

UPS capacity: check both watts and VA

Watts (W) measure real power; volt-amperes (VA) measure apparent power. Load power factor is PF = W / VA. Both the UPS’s watt and VA limits must be satisfied. Because of the difference between VA and watts, 750 VA does not automatically mean 750 W. Read the separately specified output watt rating.

A 600 W example: If the combined load power factor is 0.8, apparent power is 600 / 0.8 = 750 VA. This exceeds the watt rating of, for example, a 750 VA / 450 W UPS. A 1,000 VA / 900 W model may satisfy both limits, but that does not establish the required runtime. Assess inrush current, sudden load changes and expansion headroom separately. The example power factor is an assumption, not a value applicable to every device.

Establish the actual connected load

Include everything that must remain powered: computers, displays, routers, network switches, controllers and other equipment. Where possible, measure W and VA during normal and demanding operation, or use suitable readings from the UPS display. A computer fitted with a 750 W power supply does not necessarily consume 750 W continuously. Runtime planning uses the actual load profile; capacity selection must also account for maximum expected load and transient demands.

Why ampere-hours alone do not determine runtime

A battery’s Ah rating describes charge capacity under specified test conditions. Approximate nominal energy is Enominal ≈ V × Ah, expressed in Wh. Ah and Wh describe different quantities. For example, two identical 12 V / 9 Ah batteries connected in series form a 24 V / 9 Ah bank, not 24 V / 18 Ah. That battery bank has approximately 216 Wh of nominal energy.

Not all 216 Wh will reach the UPS output. Discharge rate, voltage drop, shutdown threshold, temperature, ageing and UPS consumption affect the result. In particular, a lead-acid battery’s Ah rating measured at a low discharge current does not translate directly into the same usable capacity during a short, high-power discharge. Dividing nameplate V × Ah by load watts is therefore not a guaranteed runtime calculation.

Calculating and checking runtime

The basic energy relationship is runtime (minutes) ≈ 60 × usable AC output energy (Wh) / load power (W). If usable energy delivered at a particular load, after losses, is 120 Wh and the constant load is 300 W, the result is 24 minutes. The 120 Wh is usable energy under those conditions, rather than the nominal battery label. For an actual selection, verify the UPS runtime calculation against the manufacturer’s curve for the exact model and battery configuration.

On the manufacturer’s runtime curve, find the connected load in watts and read the time for the installed internal or external battery arrangement. Do not assume half-load runtime is exactly twice full-load runtime: the relationship is not linear throughout. Check assumptions about battery age, charge and temperature. Critical applications also need allowance for ageing and completion of shutdown.

How to extend battery backup

Reduce unnecessary loads first. Appropriately disconnecting displays or peripherals that are not needed during an outage can preserve runtime for critical equipment. Next, consider only supported external battery accessories and compatible battery solutions. Adding batteries does not increase the UPS’s watt or VA output limit. Battery voltage, chemistry, charging capability and permitted module count must all match the system.

The distinction between online, line-interactive and offline UPS systems describes power conversion and transfer behaviour; it does not independently determine runtime. A voltage regulator and a UPS also serve different functions. Regulating voltage does not, by itself, provide stored battery energy during an outage.

How many years does the battery last?

For VRLA lead-acid batteries commonly used in small and medium UPS systems, approximately 3–5 years is a frequently quoted service life under suitable conditions. It is not a universal replacement deadline: follow the model’s maintenance plan and manufacturer guidance. Elevated temperature and frequent deep discharges can shorten life. Do not automatically apply this range to other chemistries such as lithium-ion and LiFePO4.

State of charge and battery health are different. An aged battery can indicate 100% charge yet run down quickly under load. A second outage before full recharge also reduces available time. The UPS charging system and appropriate battery charging conditions therefore matter. The service life of the UPS electronics must be assessed separately from battery life.

If the UPS shuts down sooner than it used to

Check increased load, incomplete charging, temperature and battery age. Investigate a UPS alarm or replacement warning rather than simply silencing it. A battery that appears fully charged may still lack usable capacity. Connections, charger condition and weak blocks within the bank can also reduce runtime.

Follow the manufacturer’s test procedure. Passing a short self-test does not establish full backup duration. If a controlled load test is required, plan for the connected equipment’s power needs and follow the approved service procedure. Repeatedly discharging the battery completely should not be adopted as routine maintenance; deep-discharge cycles shorten VRLA battery life.

Plan for an orderly shutdown as well as continued operation

Some applications need hours of operation; others need enough time to save data and shut down in sequence. Backing up a PLC, HMI and communications equipment requires a different power budget from supplying all the motors in a machine. Define the critical load, target runtime, shutdown time and battery configuration together before selecting the UPS.

Related technical reading

Uninterruptible power supplies; Battery banks; UPS types; mAh, Ah and Wh.