6ES7 131-4EB00-0AB0
Siemens 6ES7 131-4EB00-0AB0 – ET 200S 2DI AC120V ST Digital Input Module
Siemens 6ES7 131-4EB00-0AB0 is a two-channel, 120 V AC digital input module for SIMATIC ET 200S stations. It transfers switch and contact states to the control system. Within the Siemens ET200 family, it belongs to the ET 200S system and the digital input module product group.
Siemens specifies this order number as a packing unit containing five modules. Each individual electronic module has two input channels. State the required number of modules when requesting a replacement; packaging quantity and channel count are separate details.
Which signals does it accept?
The module transfers the states of switching devices with suitable voltage and contact ratings to the PLC program. Applications using a limit switch, pushbutton or relay contact require the field device's electrical ratings to be checked against the input conditions.
The 120 V AC input rating is a key selection detail. Finding a module of the same width in an existing station does not establish that its input voltage matches. Signals operating at 24 V DC or 230 V AC require an input module designed for the corresponding voltage.
Input voltage and logic levels
The nominal input is 120 V AC, with a frequency range of 47–63 Hz. Siemens specifies 0–20 V AC for signal “0” and 79–132 V AC for signal “1”. Voltages between those regions should not be used as a defined logic state.
If an input does not change as expected, checking whether the contact opens and closes is only part of the investigation. Review the actual terminal voltage, neutral connection, contact condition and wiring together. Mechanical operation of a switch and receipt of a valid electrical input are separate checks.
Siemens lists two-wire BERO proximity sensor connection as unsupported for this model. A mechanical contact connected with two conductors and an electronic two-wire sensor should therefore be assessed separately.
Input delay and application selection
The datasheet lists minimum input delays of 15 ms for a 0→1 transition and 25 ms for a 1→0 transition. For short pulses, assess these delays together with the PLC cycle and station data transfer.
Monitoring a machine position or operating state and counting fast pulses impose different requirements. When replacing an installed module, knowing how long the field signal normally remains active is more useful than matching channel count alone.
Terminal module and supply group
6ES7 131-4EB00-0AB0 plugs into a compatible TM-E terminal module. Siemens lists options including the screw-terminal TM-E15S24-01 / 6ES7 193-4CB20-0AA0 and spring-terminal TM-E15C24-01 / 6ES7 193-4CB30-0AA0. Check complete order numbers when matching ET200 terminal blocks and reviewing the station's connection modules.
The potential group requires a PM-E power module and terminal arrangement suitable for 120 V AC. The system manual identifies the PM-E DC24..48V/AC24..230V class for this type of application. PM-E groups designed solely for 24 V DC or 24–48 V DC are unsuitable for this AC input module.
Addressing and communication
The module occupies 1 byte without address packing or 2 bits with supported address packing. Check packing availability against the existing project and station configuration. Preserving the input addresses during replacement helps maintain the program's signal assignments.
The station's industrial communication connection is determined by its interface module. For ET 200S stations operating over PROFIBUS or PROFINET, record the interface and project definition alongside the input module's order number.
Status indicators and maintenance
Each input has a green status LED. The module itself provides no diagnostic or short-circuit diagnostic function. A channel indicator should not be interpreted as a system that separately identifies every fault in the field cable or connected switch.
During maintenance, compare the field signal, channel indicator and program input bit for the same physical point. Clearly identifying which input produces a message on the HMI panel or SCADA screen helps reduce fault-finding time.
Dimensions and electrical design
The module body measures 15 × 81 × 52 mm and weighs approximately 31 g. Typical power loss is 0.5 W; maximum consumption from the 3.3 V DC backplane bus is 6 mA. The channels are not galvanically isolated from each other; isolation is provided between the inputs and backplane bus.
For replacement, compare the complete 6ES7 131-4EB00-0AB0 label, terminal base, supply group and input addresses. Correct identification includes the signals carried by the existing field wiring as well as the module's physical position in the cabinet.
Technical documentation and related topics
For connection and configuration details, consult the relevant ET 200S documents through the Siemens ET200 PDF manuals page. Further background is available in the Siemens ET200 overview, the PROFIBUS frequently asked questions and the PLC systems and modules section.
Editor's note: The first selection check for this model is its 120 V AC input rating. Matching the ET 200S housing alone is insufficient; the terminal base, supply group and program addresses must also match the installed application.
More Siemens products: Siemens products | Siemens S7 PLC | SIMATIC S7 | ET200 products