6ES7 194-4DA00-0AA0

6ES7 194-4DA00-0AA0 Siemens ET 200pro CM F-IO 2×M12 PROFIsafe Connection Module

6ES7 194-4DA00-0AA0 is the CM F-IO 2×M12 fail-safe connection module developed for the F-Switch PROFIsafe electronic module in a Siemens SIMATIC DP ET 200pro station. Its two female M12 sockets, identified as X1 and X2, provide the physical connection between safety sensors and the fail-safe input channels of the F-Switch.

This product is not a stand-alone safety relay, a PROFIsafe electronic module or a conventional digital input block. Signal evaluation is performed by the 6ES7 148-4FS00-0AB0 F-Switch PROFIsafe electronic module. The 6ES7 194-4DA00-0AA0 provides the corresponding M12 sensor connection interface.

Product Identity and Intended Use

Product type: Fail-safe ET 200pro connection module
Siemens designation: CM F-IO 2×M12
Article number: 6ES7 194-4DA00-0AA0
System family: SIMATIC DP ET 200pro
Compatible electronic module: 6ES7 148-4FS00-0AB0 F-Switch PROFIsafe
Connections: Two female M12 circular sockets
Socket identifiers: X1 and X2
Labelling: Two connection labels and one module label
Product status: PM300 active product available for sale in Siemens Industry Mall

The F-Switch and this connection module belong within the wider group of ET 200 fail-safe modules and Siemens ET 200 PROFIsafe solutions.

The connection module does not establish a SIL or PL rating by itself. The achieved safety level depends on the sensors, F-Switch, F-CPU, wiring, parameters and validation of the complete machine safety function.

M12 Socket Pin Assignment

Pin 1: 24 V sensor supply 1, Vs1, on X1 and X2
Pin 2: Channel 2 input on X1; channel 3 input on X2
Pin 3: Sensor supply ground, 1M
Pin 4: Channel 0 input on X1; channel 1 input on X2
Pin 5: 24 V sensor supply 2, Vs2, on X1 and X2
Functional ground: FG is provided through the M12 shield

Each socket carries two input channels. For example, X1 contains channels 0 and 2. With a suitable safety sensor and correct F-Switch parameter assignment, this arrangement can support 1oo2 dual-channel evaluation through one connecting cable.

The sensor interconnection type, equivalent or nonequivalent evaluation, short-circuit test and discrepancy monitoring must still be configured correctly in the safety project.

Compatibility and Selection Checks

6ES7 194-4DA00-0AA0 is specifically the CM F-IO 2×M12 module for F-Switch PROFIsafe. Other ET 200pro fail-safe connection modules are not direct substitutes.

The 8/16 F-DI electronic module uses the 6ES7 194-4DD00-0AA0 CM IO 16×M12, while the 4/8 F-DI and 4 F-DO electronic module uses the 6ES7 194-4DC00-0AA0 CM IO 12×M12.

Before ordering, verify the full MLFB number and hardware version of the F-Switch, the ET 200pro station structure, the output type of the safety sensor, the M12 cable wiring and the STEP 7 or safety-engineering project.

Review ET 200 connection modules, ET 200 PROFIBUS and PROFINET products and other ET 200 network interfaces when checking the complete station.

Technical Data and Siemens Documentation Discrepancy

Detailed ET 200pro fail-safe manual: 45 × 130 × 40 mm
Weight stated in the same manual: 310 g
Siemens product data sheet: 90 × 130 × 39 mm
Industry Mall net weight: Approximately 0.371 kg
Connection type: 2 × female M12 sockets
Installation: Plugged onto and screwed to the F-Switch electronic module

The Siemens product data sheet and the detailed fail-safe module manual state different mechanical dimensions for the same article number. Cabinet or machine clearances should therefore not be calculated from only one online data sheet. Check the physical product label, the F-Switch station position and the actual component dimensions before installation.

Installation and Commissioning Checks

Isolate hazardous energy: Bring the machine to a safe state, isolate hazardous energy and prevent unintended restart before working on the safety circuit. Safety functions must never be bridged or defeated with temporary wiring.

Fit the correct electronic module: Align the connection module with the F-Switch electronic module, plug it in fully and secure it with the prescribed screws. Do not cross-thread M12 connectors. Connect shielding, functional ground and sensor supplies according to the Siemens terminal assignment.

Validate the safety project: Check the F-destination address, PROFIsafe parameters, channel evaluation, short-circuit test, discrepancy time and sensor supply.

Installing the correct connection module does not by itself validate the safety function. Sensor operation, cable interruption, short circuit and safe-stop behavior must be tested during commissioning.

For the remaining station hardware, review ET 200 terminal and connection blocks, ET 200 power supply modules and ET 200 power distribution modules.

Maintenance and Pre-owned Inspection

On a pre-owned module, inspect the threads and contact inserts of X1 and X2, the shield contact surfaces, housing, fastening screws and sealing areas. A unit with crushed sockets, oxidized contact surfaces or missing hardware should not be accepted for a safety circuit solely because it appears electrically intact.

Confirm that the product label reads 6ES7 194-4DA00-0AA0 and that the module has not been confused with 6ES7 194-4DC00-0AA0 or 6ES7 194-4DD00-0AA0. Record channel and cable labels before replacement, then retest F-Switch diagnostics and the actual machine safety function.

Editor’s note: Two M12 sockets do not make this a conventional two-channel input block. 6ES7 194-4DA00-0AA0 is specifically the connection module for F-Switch PROFIsafe. It cannot provide a stand-alone safety function without the correct electronic module, suitable sensor, approved wiring and validated safety program. The 45 mm versus 90 mm width discrepancy in Siemens documentation should also be checked against the physical product before ordering or installation.

Siemens PDF Documents

+ Siemens 6ES7 194-4DA00-0AA0 technical data sheet (English dynamic Siemens PDF)
+ Siemens ET 200pro fail-safe modules operating instructions (English, 07/2013, 188 pages)
+ Current Siemens TIA CM F-IO 2×M12 online documentation
+ Otomasyon AVM Siemens ET 200 PDF manual archive

Related Topics

When completing an ET 200pro station, review additional ET 200 modules and accessories, ET 200 digital output modules, ET 200 special output modules and ET 200 function modules.

Broader reference material is available in the industrial signal guide, the pre-owned industrial automation section and the Otomasyon AVM English automation resource centre.

Reminder: Siemens 6ES7 194-4DA00-0AA0 and other SIMATIC fail-safe components may be offered by Otomasyon AVM subject to availability. Units may be used or open-box products. Confirm the full model, quantity, operating condition, label photographs, socket condition and system compatibility before ordering.

Safety notice: This page supports product identification and preliminary selection. Safety-circuit design, parameter assignment, validation and periodic testing must be carried out by qualified personnel using current Siemens documentation and the machine risk assessment. Content reviewed: 30 October 2026.