6ES7 193-4CF50-0AA0
6ES7 193-4CF50-0AA0 — ET 200S TM-E30C46-A1 Terminal Module
6ES7 193-4CF50-0AA0 is the TM-E30C46-A1 terminal module in the Siemens SIMATIC product range. It is designed for compatible 30 mm electronic modules in ET 200S. Its spring terminals connect field wiring to the electronic module fitted above it.
Within the Siemens ET 200 distributed I/O range, this part belongs to ET 200S. It provides 24 terminal connections in a 4 × 6 arrangement. This does not mean 24 I/O channels: the electronic module determines the functions of terminals 1–16, while eight additional connections provide access to AUX1.
Technical specifications
Type: TM-E30C46-A1. Connection: spring terminals. Compatible module width: 30 mm. Dimensions: 30 × 157 × 43 mm (width × height × depth). Approximate weight: 131 g. Manufacturer ordering unit: 1 piece.
Why the AUX1 arrangement matters
The AUX1 bus is continuous and accessible through additional terminals. These connections are not independent signal channels; they share the auxiliary bus. The installation's electrical design determines which potential AUX1 carries. When designing an industrial automation installation, plan any required auxiliary-potential connections from the actual station wiring diagram.
Electronic module and F-module compatibility
The Siemens ET 200S fail-safe manual lists TM-E30C46-A1 among the terminal options for 4/8 F-DI DC24V PROFIsafe, 4 F-DI/3 F-DO DC24V PROFIsafe, 4 F-DO DC24V/2A PROFIsafe and 1 F-RO DC24V/AC24…230V/5A. Confirm the electronic module's complete order number and the applicable manual revision before selecting the base.
Compatibility with an F-module does not mean that the terminal base implements a safety function on its own. When selecting Siemens PLCs and accessories, assess the controller, power module and F-module together. Safety configuration in the SIMATIC S7 control system is also part of the application.
Five checks before selection
1. System and width: Confirm an ET 200S station and a compatible 30 mm electronic module. Consult the ET 200 system overview; ET 200SP and ET 200iSP bases must not be treated as the same part.
2. Terminal type: This order number uses spring terminals. 6ES7193-4CF40-0AA0 / TM-E30S46-A1 is the screw-terminal version. Check existing conductor preparation and installation requirements when considering a change.
3. Difference from 4CG30: 6ES7193-4CG30-0AA0 / TM-E30C44-01 has no terminal access to AUX1 and is 132 mm high. This 4CF50 model is 157 mm high. Check both connection requirements and cable-duct clearance before substitution.
4. Terminal numbering: Obtain the functions of terminals 1–16 from the electronic module's wiring diagram. A generic base diagram alone does not identify where a sensor or load should be connected.
5. Physical condition: Inspect the spring clamps, contacts, latches and housing. For used parts in particular, compare the complete order number on the label with the quotation.
Maintenance checks
For a channel fault, assess field wiring, the electronic module and base connections separately. Read diagnostics from the PLC and control equipment rather than diagnosing a failed base from a general alarm on an HMI operator panel or SCADA monitoring system. In applications using F-modules, complete the required functional checks after replacement under the site's safety procedures.
Editor's note: The 30 mm width is only one selection criterion. AUX1 access and the 157 mm housing height matter just as much. Do not substitute a similar-looking base without comparing the electronic module's wiring requirements.
Manuals and PDF documentation
Visit the Siemens ET 200 manuals and PDF links page. The main reference for this model is ET 200S Terminal Modules, A5E01120034-01, section 1.12 / pages 26–27. For F-module applications, also consult the module assignment table and relevant wiring diagram in ET 200S Fail-Safe, A5E00103686-08.
Related topics and Siemens navigation
Product families
Siemens main menu |
Siemens PLC products |
SIMATIC S7
ET 200 resources
ET 200 products |
ET 200 system overview |
ET 200 PDF manuals
Control and assistance
HMI operator panels |
SCADA systems |
Siemens product enquiries