6ES7 141-1BF31-0XA0

Siemens Main Menu  |  SIMATIC S7  |  Siemens ET 200  |  PDF Manuals

6ES7 141-1BF31-0XA0 - Siemens SIMATIC ET 200X EM 141 8 DI Digital Input Module

Series: SIMATIC ET 200X
Product type: EM 141 expansion module, 8 digital inputs, 24 V DC
Connection: 4 × M12 sockets, 2 inputs per socket
Order number: 6ES7141-1BF31-0XA0

6ES7 141-1BF31-0XA0 is an ET 200X EM 141 digital-input expansion module in the Siemens ET 200 distributed I/O family. It collects eight 24 V DC inputs through four M12 sockets and is intended for field connection of switches and proximity sensors.

An ET 200X expansion module, not a basic module

This product has no independent PROFIBUS address or communication interface. It installs beside an ET 200X basic module; input states and sensor power pass through the backplane bus. The SIMATIC S7 automation system sees it as part of the attached ET 200X station hardware configuration.

It is therefore not a stand-alone eight-input field station. When assessing the ET 200 system architecture, check the exact basic-module order number, product revision, available expansion position and STEP 7 hardware catalog. Similar connector geometry does not make it compatible with another ET 200 family.

Key technical specifications

Digital inputs: 8.
Rated input voltage: 24 V DC.
Signal 1: 13 to 30 V; typical input current 7 mA.
Signal 0: -3 to +5 V.
Input characteristic: IEC 61131 Type 1.
Input delay: 1.2 to 4.8 ms for both 0→1 and 1→0.
Two-wire sensor: supported; permissible quiescent current 1.5 mA maximum.
Simultaneous inputs: all 8 up to 55 °C.
Cable length: 30 m maximum, unshielded.
Electrical isolation: none.
Backplane 1L+ current: 16 mA maximum.
Power loss: typically 1.5 W.
Dimensions: 87 × 110 × 55 mm.
Weight: approximately 250 g.

When comparing ET 200 digital input modules, “8 DI / 24 V DC” is not enough. Input type, M12 pin assignment, diagnostic capability, module length and basic-module compatibility must all match.

Eight inputs across four M12 sockets

Each of sockets X1-X4 carries two input signals. Pin 4 carries channels 0, 1, 2 and 3; pin 2 carries channels 4, 5, 6 and 7. X1 therefore contains channels 0 and 4, X2 contains 1 and 5, X3 contains 2 and 6, and X4 contains 3 and 7. Pin 1 is sensor supply 1L+, pin 3 is sensor/electronics ground 1M and pin 5 is PE.

A conventional three-wire M12 sensor cable normally uses the first channel on pin 4. Reaching the second channel on pin 2 requires the appropriate dual-input cable or splitter. When choosing ET 200 connection modules and M12 connectors, do not assume that four sockets mean only four inputs.

Total sensor-supply current matters

The module provides four electronically short-circuit-protected sensor-supply outputs. Siemens specifies a combined output-current limit of 0.9 A up to 40 °C and 0.7 A up to 55 °C. The permissible total current for the complete ET 200X station must also be observed.

When designing the ET 200 power supply arrangement and ET 200 field power distribution, include the combined current and startup behavior of two sensors sharing one M12 socket. An unloaded voltage reading at pin 1 does not prove that the supply remains adequate under load.

Do not confuse it with the diagnostic version

6ES7141-1BF31-0XA0 is a standard input module, not the channel-diagnostic DIAG version. It has one green status LED per channel but generates no alarms. Do not assume the channel short-circuit and wire-break diagnostics, hardware interrupts or parameterizable input delays provided by 6ES7141-1BF30-0XB0 DIAG.

Likewise, 6ES7141-1BF41-0XA0 is an eight-input standard module but uses a 180 mm long housing; this 1BF31 model is the 110 mm short version. Check mechanical size as well as electrical data and the project record. The ET 200 PROFIBUS interface belongs to the basic module, so a network fault should not automatically be blamed on this input expansion module.

Six field checks for commissioning

1. Verify basic-module compatibility. Read the complete ET 200X basic-module order number and product revision, then compare them with the STEP 7 hardware configuration.

2. Map all eight channels correctly. Channels 0-3 are on pin 4 and channels 4-7 are on pin 2. Label the physical socket against the PLC address.

3. Measure total sensor current. Keep the combined load on the four 1L+ outputs below the applicable 0.9 A or 0.7 A temperature-dependent limit.

4. Do not mistake a status LED for a diagnostic alarm. The green LED confirms electrical input state only. Wire break, sensor misalignment and process failure need separate checks.

5. Seal unused M12 connections. Correct M12 caps are required to maintain IP65, IP66 or IP67 protection. Prepare the ET 200 field connection arrangement for water, oil and vibration exposure.

6. Separate standard signals from safety inputs. This module is not a PROFIsafe F-DI. Emergency-stop, guard-door and light-curtain signals require suitable ET 200 safety modules and a validated safety architecture.

Used-unit inspection

Confirm the full 6ES7141-1BF31-0XA0 code and product revision. Inspect the threads, pins, seals and caps of all four M12 sockets, every channel LED and the side expansion connection. Oxidized pins, a broken seal or a cracked housing are functional risks, not cosmetic faults. Missing parts may be completed from ET 200 accessories and supplementary modules; label and connector photographs can be sent through the Otomasyon AVM Siemens contact page.

Editor’s note

The most common mistakes are reading four M12 sockets as four inputs and treating the standard 1BF31 as equivalent to the diagnostic 1BF30-0XB0. This product is also an ET 200X expansion module, not an independent PROFIBUS device. On a used unit, inspect the side bus connection and every M12 seal instead of judging only the clean front face.

PDF manuals and documentation

Consult ET 200X Distributed I/O Device, Edition 02/2003, EWA 4NEB 780601602-06 on the Siemens ET 200 PDF manuals page. Section 7.8 gives the exact model pin assignment, basic circuit and technical data. For final selection, use the device label, product revision, basic module, STEP 7 hardware record and manufacturer manual together.