6ES7 138-4DE01-0AB0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 138-4DE01-0AB0 — Siemens ET 200S 1 COUNT 5 V/500 kHz Counter Module
6ES7 138-4DE01-0AB0 is a single-channel, 32-bit counter module for the ET 200S series within the Siemens ET 200 distributed I/O family. It counts pulses from RS422 incremental encoders and supplies motion-related measurement data to a SIMATIC S7 control system.
Counting and measurement tasks
The module supports continuous, once-only and periodic counting, plus frequency, rotational-speed and period measurement. When selecting ET 200 digital input modules, assess whether dedicated counter hardware is needed for fast encoder pulses. Consider encoder resolution, mechanical transmission and the selected evaluation mode together.
Key technical details
Order number: 6ES7138-4DE01-0AB0.
Designation: 1 COUNT 5 V/500 kHz.
Counter: 1 channel, 32 bit.
Encoder interface: 5 V differential RS422 incremental signals.
Maximum input frequency: 500 kHz.
Rated load supply L+: 24 V DC.
Module width: 30 mm.
Outputs: 2 integrated digital outputs, usable for comparison results.
Synchronous operation: Isochronous operation with a suitable system configuration.
The 5 V designation identifies the encoder signal class; it must not be confused with the module’s L+ supply. Check the encoder’s own supply rating separately. When selecting ET 200 power supply modules and reviewing the ET 200 power distribution arrangement, distinguish supply terminals from signal terminals.
Five selection and commissioning checks
1. Verify the encoder output. An “incremental encoder” label alone is insufficient. Confirm RS422 outputs and match the A/B channels and, where required, the reference signal to the project wiring. Do not assume that a 24 V HTL output can connect directly to a 5 V RS422 counting input.
2. Calculate the pulse frequency. An encoder producing 1,024 pulses per revolution on each channel at 3,000 rpm generates 51.2 kHz: 1,024 × 3,000 / 60. Double or quadruple evaluation changes the resulting count; this is distinct from the physical frequency on an encoder channel.
3. Inspect the terminal base and shielding. Select ET 200 terminal blocks by terminal arrangement and the exact module’s wiring diagram as well as width. When checking ET 200 connection modules and encoder cabling, examine differential pairs and shielding together. Identify missing shielding components among the required ET 200 additional modules and accessories.
4. Check the station for synchronous operation. Isochronous capability is not enabled automatically in every installation. Verify that the installed IM151, CPU and project settings support the intended operation when reviewing ET 200 PROFIBUS and PROFINET interfaces. Siemens includes the 4DE01 in its PROFIBUS DP isochronous-module list.
5. Assess replacements against the project. Siemens identifies 6ES7138-4DE02-0AB0 as a compatible replacement for the 4DE01. Within the existing ET 200 system architecture, still compare terminal wiring, hardware-catalogue selection, parameters and I/O addresses. Do not assume that features added to a later version are available on an installed 4DE01.
Editor’s note
A changing counter value does not prove that the measurement is scaled correctly. For an initial check, turn the encoder through one known revolution and compare the count change with the expected result, then check direction and reference behaviour. If the result differs by a factor of two or four, review pulse evaluation. Share the module label, encoder label and project settings together through the Otomasyon AVM Siemens contact page to make a product assessment easier.
PDF manuals and documentation
Look for Technological Functions documents on the Siemens ET 200 PDF manuals page. IK PI 2005, printed pages 6/62–6/64, contains the 4DE01 technical and ordering information. A5E00140278-02 lists counting and measurement options; A5E00124867-06, section 3.1, documents the compatible replacement of the 4DE01 by the 4DE02. For detailed settings, check the order number and version covered by the document.
Related topics and Siemens navigation
Digital input modules | Terminal blocks | Communication interfaces
Power supply modules | Additional modules and accessories | ET 200 system architecture
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals