6ES7 132-4BD31-0AA0

Siemens 6ES7132-4BD31-0AA0 ET 200S 4 DO 24 V DC / 2 A ST Module

6ES7132-4BD31-0AA0 is a four-channel, 24 V DC / 2 A Standard (ST) digital output module for SIMATIC ET 200S. This 15 mm-wide electronic module forms part of the Siemens industrial automation range and controls suitable solenoid valves, DC contactors and indicator lights.

Within the Siemens ET 200 distributed I/O family, it fits an ET 200S station and receives its load supply through the station's power module. In industrial automation applications, selection must account for the combined current of simultaneously active loads as well as the number of outputs.

Four outputs with a 4 A module limit

The rated current is 2 A per output, while the maximum combined output current is 4 A per module. Four channels therefore cannot supply 2 A each simultaneously to provide 8 A. For example, four 1.5 A loads operating together draw 6 A and exceed the module limit. In PLC-based control applications, check the output combinations that the program can activate together, rather than assessing each coil in isolation.

Five checks before selection or replacement

1. Electrical load characteristics: At signal “1”, the output voltage is at least L+ − 1 V. The specified minimum load current is 7 mA, and residual current at signal “0” is up to 0.5 mA. Check the off-state behavior of low-current electronic inputs or LED loads, and account for voltage drop along the cable.

2. Terminal module: Compatible examples include TM-E15S24-01 / 6ES7193-4CB20-0AA0 and TM-E15C24-01 / 6ES7193-4CB30-0AA0. When reviewing ET 200 system architecture and terminal selection, confirm the complete base code and M connections. The output channels are not galvanically isolated from one another.

3. Supply and protection: Each channel has short-circuit protection, but cable sizing, power supply selection and potential-group design still require attention. Outputs must not be paralleled to increase current capacity. Siemens also notes that reversed supply polarity can cause the outputs to conduct; verify L+ and M before commissioning.

4. Switching frequency: The specified limits are 100 Hz for resistive loads, 2 Hz for a 0.5 H inductive load and 10 Hz for lamp loads. Maximum lamp load is 10 W. In fast-cycling SIMATIC S7 control applications, do not apply the 100 Hz figure directly to a solenoid coil; the load category determines the relevant limit.

5. Status indication and troubleshooting: Each channel has a green LED, but the technical specifications state that the module has no diagnostic function. An illuminated LED does not prove that an actuator has moved. Assess commands displayed on HMI operator panels together with field feedback and the condition of the load circuit.

Relationship between 4BD31 and 4BD32

Siemens lists 6ES7132-4BD32-0AA0 as the successor in its module compatibility documentation. When selecting replacements from the Siemens PLC and I/O range, treat this as a starting point: verify the interface module, hardware catalog, project configuration and application-specific approvals. A “4 DO / 2 A” description alone is insufficient to establish replacement suitability.

Manuals and technical assessment

For terminal assignments and load limits, use the 4DO DC24V/2A ST – 6ES7132-4BD31-0AA0 device manual through the Siemens ET 200 PDF manuals page. For component matching, provide the module label, terminal code, power module details and currents of simultaneously active loads through Siemens product technical enquiries.

Editor's note: The easily missed distinction is between 2 A per channel and 4 A for the complete module. A valve that operates correctly on its own may behave differently when other loads switch on. During troubleshooting, examine simultaneous switching events and the 24 V supply as well.

Related topics and Siemens navigation

Product families
Siemens main menu  |  Siemens PLC products  |  SIMATIC S7

ET 200 resources
ET 200 products  |  ET 200 system overview  |  ET 200 PDF manuals

Control and assistance
HMI operator panels  |  SCADA systems  |  Siemens product enquiries