6ES7 132-4BD01-0AA0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 132-4BD01-0AA0 — Siemens ET 200S 4 DO 24 V DC/0.5 A ST Digital Output Module
6ES7 132-4BD01-0AA0 is a four-channel standard digital output module for the ET 200S series in the Siemens ET 200 distributed I/O family. It operates 24 V DC solenoid valves, DC contactors and indicator lamps from a SIMATIC S7 control system.
Output arrangement and current limit
Each of the four outputs has a nominal rating of 0.5 A, and the permitted total current for all outputs is 2 A. Do not treat modules as equivalent by looking only at the “4 DO” part of the designation. In particular, 6ES7132-4BD32-0AA0 belongs to the 2 A-per-channel class and is not a like-for-like current-rating substitute. When comparing ET 200 digital output modules, calculate continuous load current, pickup current and the total for the common power group.
Key technical details
Order number: 6ES7132-4BD01-0AA0.
Designation: 4 DO DC24V/0.5A ST.
Outputs: 4.
Rated current per channel: 0.5 A.
Permissible channel current: 7 mA to 0.6 A.
Total module current: 2 A maximum.
Load voltage: 24 V DC from the power module.
Dimensions: 15 × 81 × 52 mm.
Weight: approximately 40 g.
Address space: 4 bits when packed; 1 byte when unpacked.
Typical power loss: 0.8 W.
Factory package: 5 electronic modules per packing unit.
The outputs are short-circuit protected, with a short-circuit threshold of 0.7 to 1.5 A. Siemens specifies a signal-1 output voltage of at least L+ minus 1 V, approximately 100 µs turn-on delay and 300 µs turn-off delay. Each channel has a green status LED, but this ST version has no channel diagnostic function. Detailed channel fault information should therefore not be expected through the ET 200 PROFIBUS or PROFINET interface.
Five selection and commissioning checks
1. Calculate load current and power-group demand. The continuous load on each channel must remain within the nominal 0.5 A rating, while the sum of all four channels must remain within 2 A. Include pickup current for solenoids and contactors. Check the capacity of the ET 200 power supply module and ET 200 power distribution arrangement together with other modules in the same potential group.
2. Identify the correct terminal base. The Siemens manual lists twelve compatible terminal modules. Spring types include 6ES7193-4CA50/30 and 4CB30/10; screw types include 4CA40/20 and 4CB20/00; Fast Connect types include 4CA80/70 and 4CB70/60. Select ET 200 terminal modules by AUX1 arrangement, terminal count and wiring method.
3. Do not parallel outputs to increase current. Two channels may control one load redundantly, but Siemens does not permit parallel connection for uprating. If more current is required, use the ET 200 connection arrangement to assess a suitable interposing relay, contactor or higher-current output module.
4. Match the load type and switching rate. Maximum switching frequency is 100 Hz with a resistive load, 2 Hz with a 0.5 H inductive load and 10 Hz with a lamp load. Lamp load is limited to 5 W per channel. The documented cable limits of 600 m unshielded and 1000 m shielded do not replace conductor-sizing and voltage-drop calculations.
5. Verify replacement and energisation conditions. Siemens identifies the 4BD01 as the replacement type for 6ES7132-4BD00-0AA0. Within the ET 200 system architecture, still compare hardware-catalogue selection, address packing, terminal code and power group. Because reverse polarity can cause outputs to switch through, verify L+ and M before applying power. The five-unit factory package must not be confused with the actual quantity in field stock or a used-equipment listing.
A 50 µs pulse that can be missed during commissioning
According to the Siemens manual, when the 24 V DC load voltage is applied to the power module through a mechanical contact, the digital outputs can carry a “1” signal for approximately 50 µs due to switching. Account for this behaviour when the module is used with fast digital inputs, counters or circuits sensitive to short pulses.
Editor’s note
If an output does not operate, the channel LED alone is insufficient because the ST version provides no detailed channel diagnostics. Measure L+ and M with the load connected, channel current, the common power group and terminal tightness. Keep 4BD01 and 4BD32 clearly separated: one is rated at 0.5 A per channel and the other at 2 A per channel. Share the module label, terminal-base code and load data together through the Otomasyon AVM Siemens contact page to make the product assessment more reliable.
PDF manuals and documentation
Consult A5E01077208-01 — 4DO DC24V/0.5A ST on the Siemens ET 200 PDF manuals page. The manual documents terminal assignments, compatible terminal bases, the 2 A total-current limit and 50 µs switching behaviour specifically for the 6ES7132-4BD01-0AA0. Use it alongside the ET 200S station manual when selecting ET 200 accessories and separation components.
Related topics and Siemens navigation
Digital output modules | Terminal modules | Power supply modules
Power distribution modules | Communication interfaces | ET 200 system architecture
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals