6ES7 151-7AA11-0AB0

Siemens 6ES7 151-7AA11-0AB0 – ET 200S IM151-7 CPU

The 6ES7 151-7AA11-0AB0 is an IM151-7 CPU module for the Siemens ET 200S distributed I/O system. Its CPU runs the user program and can control a machine locally through suitable input and output modules installed on the station.

It can operate as a standalone control station or exchange data with a higher-level controller as a PROFIBUS DP slave, depending on the project. See What is a PLC CPU? for the general role of a controller CPU.

Work memory and module capacity

Siemens product information specifies 64 KB of work memory for this model. Work memory is used by the CPU to execute the program and is different from MMC storage capacity. Inserting a larger memory card does not increase the CPU's 64 KB work memory.

With a suitable configuration, the station can be expanded with up to 63 ET 200S modules. Also check station width, backplane load, address space and module compatibility when selecting digital, analog and power modules.

Supply and PROFIBUS connection

The device uses a 24 V DC supply. Its integrated PROFIBUS DP / MPI interface uses a 9-pin female Sub-D connection for copper wiring. When communicating with a higher-level controller, check the station address, connector, cable and bus termination together. See PROFIBUS and PROFINET for the network principles.

The integrated interface supports PROFIBUS DP slave operation. If a separate PROFIBUS DP master line is required, the 6ES7 138-4HA00-0AB0 DP master module can be considered in a suitable system configuration. Verify the expansion and connected devices against the project.

SIMATIC MMC memory card

The IM151-7 CPU uses a SIMATIC Micro Memory Card to store the user program and associated data. Siemens' card-compatibility information lists up to 8 MB for this order number; the card's exact order number and device version should still be checked.

A blank card does not automatically receive the machine program. Before replacement, back up the running program and engineering project. Program blocks on the card do not prove that a complete project archive with symbols and comments is also present. Other cards are listed under used memory cards.

Do not remove the card while the CPU is in RUN. Stop the CPU and ensure that writing has finished according to the device instructions. Do not format a SIMATIC MMC with Windows; the card structure and program data can be damaged.

Programming and model differences

Siemens' hardware-support information lists STEP 7 V5.2 SP1 for this model. Check that the CPU appears in the hardware catalogue of the installed STEP 7 version and install the appropriate hardware support package if required. General information is available under PLC programming software.

7AA11, 7AA10, 7AA13 and 7AB00 are different versions. For example, Siemens product information specifies 64 KB for 7AA11 and 96 KB for 7AA13. The 7AB00 is the fiber-optic FO version. Compare the complete order number, firmware, project and connection type before replacement.

Troubleshooting

If the CPU remains in STOP, first check the 24 V supply, MMC and the diagnostic buffer in STEP 7. Do not format the card or load another program before investigating a memory-reset request and preserving the required data.

For PROFIBUS faults, check the station address, Sub-D connector, termination, cable and higher-level controller configuration. If a local input or output does not work, inspect its ET 200S module, power module and field wiring. See PLC troubleshooting for a general checking sequence.

Editor's Note: The CPU, MMC and field modules form one system. A working replacement 7AA11 alone does not guarantee that the machine will run: the correct program, card, PROFIBUS address and module arrangement must also match the project. Verify the backup before changing the card.

Manuals and related topics

For mounting, programming, MMC and diagnostics, visit Siemens ET 200 manuals and PDF files. See About Siemens ET 200 for the family overview.

Related topics: What is a PLC? · Used PLC CPUs · ET 200 communication modules · Operator panels

Navigation: Siemens automation · SIMATIC S7 · Siemens ET 200 · OtomasyonAVM homepage