6ES5 281-4UA11

Siemens 6ES5 281-4UA11 IP 281 High-Speed Counter Module

The 6ES5 281-4UA11 is the IP 281 base counter module with a 24 V encoder supply for SIMATIC S5. This S5 special module provides one counter channel for high-speed pulse counting up or down in 16- or 32-bit mode. Its maximum input frequency is 250 kHz with suitable signals and filter settings.

Encoder, power and field connections

Connect the first incremental encoder to the 15-pin Sub-D socket X5. With a second counter fitted, its encoder connects to X7. IP 281 accepts 24 V or 5 V RS-422 encoder signals for A/B and the index pulse. Match the encoder cable to the signal type and reference connection. The external 24 V DC supply enters at X3. The 4UA11 provides 24 V encoder power. Siemens lists 4UP11 for installations requiring an onboard 5.2 V encoder supply.

X4 carries counter 1’s STA, STO and SET digital inputs and its DQ output. X6 provides the same connections for counter 2. A configured comparison event can trigger DQ. After startup, the PLC program enables the output through control register 3.

CPU support, addressing and second channel

The Siemens manual lists CPUs and rack slots for S5-115U/H, S5-135U and S5-155U/H. Examples include the CPU 944B in 115U, CPU 922 and CPU 928 in 135U, CPU 946 in 155U and CPU 946R in 155H. The S5 PLC program accesses IP 281 registers directly. Match the S1 base address setting to the program and verify the selected slot.

The 1992 IP 281 manual lists 6ES5 281-4UB11 for the second counter. ST 50 lists 4UB12 alongside the 4UA12 and 4UP12 base modules. Match the full base module and submodule order numbers when choosing a spare. The IP 242A, IP 242B and 385B belong to other S5 counter families.

Editor’s note

Record the settings before removal. Follow the plant isolation procedure. Photograph the S1 address switch, filter jumpers and connector labels for X3 through X7.

Check RS-422 signal level and encoder supply separately. Read both the A/B signal type and supply voltage from the encoder data sheet. Match each to the X5 connection table.

Check the gate if pulses arrive but the count stands still. Verify the configured hardware or software gate in the PLC. For 24 V inputs, compare the filter jumper settings with the measured pulse frequency.

Read status register 3 when ERR lights. Distinguish an invalid operating mode from an active RS-422 wire-break indication. Trace the parameters for the former and the encoder cable and connector for the latter.

Trace the DQ circuit if the count changes but the field output stays off. Check the comparison value, output enable in control register 3 and the X3 supply. Verify counter 1’s physical DQ output at X4.

Verify the channel count when buying used. Ask for a count in both directions and a DQ test on counter 1. If a second channel is offered, request the submodule label and its presence indication in the status register.

To offer an IP 281 for sale, send the full label, front connector photos, any submodule order number and test results to otomasyonavm@gmail.com.

PDF manuals and wiring diagrams

+ Siemens IP 281 equipment manual (English PDF) · Connectors §1.3.3, S1 §2.2, diagnostics §5 and specifications §8. See p. 1-2 for the order number.

+ Siemens ST 50 catalog (English PDF) · pp. 4/79–4/80, IP 281 and 4UB12 ordering table.

+ Shared S5 PDF archive

Related topics

+ 6ES5 281-4UB12 IP 281 submodule

+ What is a high-speed counter?

+ About Siemens S5 PLC

Navigation

+ S5 Special Modules

+ SIMATIC S5

+ Second-hand Siemens